XRT79L71IB datasheet(11/109 Pages) EXAR

11 / 109 page

XRT79L71

REV. 1.0.0

1-CHANNEL DS3/E3 ATM UNI/PPP/CLEAR-CHANNEL FRAMER IC - HARDWARE

C14

RDY/DTACK/

RDY

READY or DTACK Output:

The exact function of this input pin depends upon which mode the Microprocessor

Interface has been configured to operate in.

Intel-Asynchronous Mode - RDY - Ready Output:

If the Microprocessor Interface has been configured to operate in the Intel-Asynchro-

nous Mode, then this output pin functions as the active-"Low" READY output.

During a READ or WRITE cycle, the Microprocessor Interface block toggles this out-

put pin to the logic "Low" level ONLY when it (the Microprocessor Interface) is ready

to complete or terminate the current READ or WRITE cycle. Once the Microproces-

sor has determined that this input pin has toggled to the logic "Low" level, then it is

now safe for it to move on and execute the next READ or WRITE cycle.

If (during a READ or WRITE cycle) the Microprocessor Interface block is holding this

output pin at a logic "High" level, then the Microprocessor is expected to extend this

READ or WRITE cycle, until it detects this output pin being toggled to the logic "Low"

level.

Motorola-Asynchronous Mode - DTACK - Data Transfer Acknowledge Output

If the Microprocessor Interface has been configured to operate in the Motorola-Asyn-

chronous Mode, then this output pin will function as the active-"Low" DTACK output.

During a READ or WRITE cycle, the Microprocessor Interface block will toggle this

output pin to the logic "Low" level, ONLY when it (the Microprocessor Interface) is

ready to complete or terminate the current READ or WRITE cycle. Once the Micro-

processor has determined that this input pin has toggled to the logic "Low" level, then

it is now safe for it to move on and execute the next READ or WRITE cycle.

If (during a READ or WRITE cycle) the Microprocessor Interface block is holding this

output pin at a logic "High" level, then the Microprocessor is expected to extend this

READ or WRITE cycle, until it detects this output pin being toggled to the logic "Low"

level.

Power PC 403 Mode - RDY - Ready Output:

If the Microprocessor Interface has been configured to operate in the Power PC 403

Mode, then this output pin will function as the active-"High" READY output.

During a READ or WRITE cycle, the Microprocessor Interface block toggles this out-

put pin to the logic "High" level ONLY when it (the Microprocessor Interface) is ready

to complete or terminate the current READ or WRITE cycle. Once the Microproces-

sor has sampled this signal being at the logic "High" level (upon the rising edge of

PCLK), then it is now safe for it to move on and execute the next READ or WRITE

cycle.

If during a READ or WRITE cycle the Microprocessor Interface block is holding this

output pin at a logic "Low" level, then the Microprocessor is expected to extend this

READ or WRITE cycle, until it samples this output pin being at the logic "Low" level.

NOTE: The Microprocessor Interface updates the state of this output pin upon the

rising edge of mPCLK.

M14

RESET

Hardware Reset Input:

When this active-"Low" signal is asserted, the XRT79L71 will be asynchronously

reset. When this occurs, all outputs will be tri-stated and all on-chip registers will be

reset to their default values.

PIN DESCRIPTIONS

PIN #NAME

TYPE

DESCRIPTION

XRT79L71IB датащи(PDF) 11 Page - Exar Corporation

XRT79L71IB датащи(HTML) 11 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL