AT43USB353M datasheet(80/95 Pages) ATMEL

80 / 95 page

AT43USB353M

3307B–USB–4/04

Set by hardware due to babble, physical disconnect or overcurrent except for Port 1 in which

case it is set by hardware at EOF2 due to hardware events. Cleared by firmware via Host

request ClearPortFeature(PORT_ENABLE).

• Bit 0 – PCSC: Port Connect Status Change

0 = No change has occurred on Current Connect Status

1 = Current Connect Status has changed

This bit is set by hardware at EOF2 after it detects a connect or disconnect at a port, except for

Port 1. Hardware sets this bit for Port 5 after a hub reset. Cleared by firmware via Host request

ClearPortFeature(PORT_CONNECTION).

Hub and Port Power

Management

Overcurrent protection and power switching is required for the external downstream ports

only. In the AT43USB353M, these tasks are completely programmable. This means that any

type of hub is achievable with the AT43USB353M: self-powered or bus-powered hubs, per

port or global overcurrent protection, individual or ganged port power switching.

The use of the MCU's GPIO pins are required to interface to the external power supply moni-

toring and switching. The on-chip hardware of the AT43USB353M contains the circuitry to

handle all the possible combinations of port power management tasks. The firmware defines

the exact configuration.

Overcurrent Sensing

The AT43USB353M is capable of detecting overcurrent during active operation only, or during

any condition even when the hub is in the suspended state. When overcurrent in the active

state only is desired, any GPIO pin of the AT43USB353M can be used to sense and the over-

current condition. Control of the condition must be performed by the firmware. If overcurrent

detection under any condition is desired, then specific GPIO pins must be used to sense the

overcurrent and the proper bit(s) of UOVCER set. In Global Overcurrent Protection mode,

overcurrent sensing must be routed to GPIO PD0. In Individual Port Overcurrent Protection

mode Port2 and Port 3 overcurrent sensing must be assigned to GPIO PD0 and PD1. In the

following description, it is assumed that overcurrent protection is required under any condition.

Global Overcurrent Protection – In this mode, the Port Overcurrent Indicator and

Port Overcurrent Indicator Change should be set to 0's. For the AT43USB353M an

external solid state switch, such as the Micrel MIC2025-2, is required to switch power

to the external USB ports. The FLG output of the switch should be connected to PD0.

When an overcurrent occurs, FLG is asserted and the firmware should set the Hub

Overcurrent Indicator and Hub Overcurrent Indicator Change and switch off power to

all external downstream ports. The hub status change is reported on the next IN token

through the hub's interrupt endpoint, Endpoint1.

Individual Port Overcurrent Protection – The Hub Overcurrent Indicator and Hub

Overcurrent Indicator Change bits should be set to 0's. One MIC2026-2 is required for

the two USB ports. The FLG output of the MIC2026-2 associated with Port2 should be

connected to GPIO PD0 and the other FLG output to PD1. An overcurrent is indicated

by assertion of FLG. The firmware sets the corresponding port's Overcurrent Indicator

and the Overcurrent Indicator Change bits and switches off power to the port. At the

next IN token from the Host, the AT43USB353M reports the port status change through

the hub's Endpoint1.

AT43USB353M датащи(PDF) 80 Page - ATMEL Corporation

AT43USB353M датащи(HTML) 80 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

датащи скачать

ссылки URL