MMPF0200Z datasheet(89/118 Pages) NXP

89 / 118 page

Analog Integrated Circuit Device Data



Freescale Semiconductor

PF0200Z

Functional Block Requirements and Behaviors

Control Interface I2C Block Description

Figure 23. I2C Read Example

6.5.3

Interrupt Handling

The system is informed about important events based on interrupts. Unmasked interrupt events are signaled to the processor by

driving the INTB pin low.

Each interrupt is latched so that even if the interrupt source becomes inactive, the interrupt will remain set until cleared. Each

interrupt can be cleared by writing a “1” to the appropriate bit in the Interrupt Status register; this will also cause the INTB pin to

go high. If there are multiple interrupt bits set the INTB pin will remain low until all are either masked or cleared. If a new interrupt

occurs while the processor clears an existing interrupt bit, the INTB pin will remain low.

Each interrupt can be masked by setting the corresponding mask bit to a 1. As a result, when a masked interrupt bit goes high,

the INTB pin will not go low. A masked interrupt can still be read from the Interrupt Status register. This gives the processor the

option of polling for status from the IC. The IC powers up with all interrupts masked, so the processor must initially poll the device

to determine if any interrupts are active. Alternatively, the processor can unmask the interrupt bits of interest. If a masked interrupt

bit was already high, the INTB pin will go low after unmasking.

The sense registers contain status and input sense bits so the system processor can poll the current state of interrupt sources.

They are read only, and not latched or clearable.

Interrupts generated by external events are debounced; therefore, the event needs to be stable throughout the debounce period

before an interrupt is generated. Nominal debounce periods for each event are documented in the INT summary Table 100 . Due

to the asynchronous nature of the debounce timer, the effective debounce time can vary slightly.

6.5.4

Interrupt Bit Summary

Table 100 summarizes all interrupt, mask, and sense bits associated with INTB control. For more detailed behavioral

descriptions, refer to the related chapters.

Table 100. Interrupt, Mask and Sense Bits

Interrupt

Mask

Sense

Purpose

Trigger

Debounce Time (ms)

LOWVINI

LOWVINM

LOWVINS

Low Input Voltage Detect

Sense is 1 if below 2.80 V threshold

H to L

3.9(68)

PWRONI

PWRONM

PWRONS

Power on button event

H to L

31.25(68)

Sense is 1 if PWRON is high.

L to H

31.25

THERM110

THERM110M

THERM110S

Thermal 110 °C threshold

Sense is 1 if above threshold

Dual

3.9

THERM120

THERM120M

THERM120S

Thermal 120 °C threshold

Sense is 1 if above threshold

Dual

3.9

THERM125

THERM125M

THERM125S

Thermal 125 °C threshold

Sense is 1 if above threshold

Dual

3.9

THERM130

THERM130M

THERM130S

Thermal 130 °C threshold

Sense is 1 if above threshold

Dual

3.9

SW1AFAULTI

SW1AFAULTM

SW1AFAULTS

Regulator 1A overcurrent limit

Sense is 1 if above current limit

L to H

8.0

SW1BFAULTI

SW1BFAULTM

SW1BFAULTS

Regulator 1B overcurrent limit

Sense is 1 if above current limit

L to H

8.0

Device

Address

Device Address

Packet

Type

START

R/W

STOP

START

R/W

PMIC Driven Data

Host can also

drive another

Start instead of

Stop

Host SDA

Slave SDA

MMPF0200Z датащи(PDF) 89 Page - NXP Semiconductors

MMPF0200Z датащи(HTML) 89 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL