MEC1322 datasheet(300/456 Pages) MICROCHIP

300 / 456 page

MEC1322

DS00001719D-page 300

 2014 - 2015 Microchip Technology Inc.

Offset

03h

Bits

Description

Type

Default

Reset

Event

7 MCHP Reserved

R/W

VCC1_R

ESET

6 EN_RRC

Enables the ramp rate control circuitry during the Manual Mode of

operation.

• ‘0’ (default) - The ramp rate control circuitry for the Manual

Mode of operation is disabled. When the Fan Drive Setting val-

ues are changed and the RPM based Fan Control Algorithm is

disabled, the fan driver will be set to the new setting immedi-

ately.

• ‘1’ - The ramp rate control circuitry for the Manual Mode of oper-

ation is enabled. The PWM setting will follow the ramp rate con-

trols as determined by the Fan Step and Update Time settings.

The maximum PWM step is capped at the Fan Step setting and

is updated based on the Update Time as given by Table 26-11,

"Update Time".

R/W

VCC1_R

ESET

5DIS_GLITCH

Disables the low pass glitch filter that removes high frequency noise

injected on the TACH pin.

• ‘0’ (default) - The glitch filter is enabled.

• ‘1’ - The glitch filter is disabled.

R/W

VCC1_R

ESET

4:3 DER_OPT[1:0]

Control some of the advanced options that affect the derivative por-

tion of the RPM based fan control algorithm as shown in Table 26-

12, "Derivative Options". These bits only apply if the Fan Speed

Control Algorithm is used.

R/W

11b

VCC1_R

ESET

2:1 ERR_RNG[1:0]

Control some of the advanced options that affect the error window.

When the measured fan speed is within the programmed error win-

dow around the target speed, the fan drive setting is not updated.

These bits only apply if the Fan Speed Control Algorithm is used.

See Table 26-13, "Error Range Options".

R/W

01b

VCC1_R

ESET

0POLARITY

Determines the polarity of the PWM driver. This does NOT affect the

drive setting registers. A setting of 0% drive will still correspond to

0% drive independent of the polarity.

• ‘0’ (default) - the Polarity of the PWM driver is normal. A drive

setting of 00h will cause the output to be set at 0% duty cycle

and a drive setting of FFh will cause the output to be set at

100% duty cycle.

• ‘1’ - The Polarity of the PWM driver is inverted. A drive setting of

00h will cause the output to be set at 100% duty cycle and a

drive setting of FFh will cause the output to be set at 0% duty

cycle.

R/W

VCC1_R

ESET

MEC1322 датащи(PDF) 300 Page - Microchip Technology

MEC1322 датащи(HTML) 300 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL