| поискавой системы для электроныых деталей |
|
DAC5687IPZP датащи(PDF) 54 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
DAC5687IPZP датащи(HTML) 54 Page - Texas Instruments |
|
54 / 79 page ![]() www.ti.com IOUT1 4:1 IOUT2 100 Ω 100 Ω RLOAD 50 Ω AVDD (3.3 V) AVDD (3.3 V) S0033-02 Combined Output Termination S0069-01 IOUTA1 1:1 RLOAD 50 Ω IOUTA2 AVDD (3.3 V) IOUTB1 IOUTB2 DAC5687 SLWS164E – FEBRUARY 2005 – REVISED SEPTEMBER 2006 Figure 61. Driving a Doubly Terminated 50- Ω Cable Using a 4:1 Impedance Ratio Transformer The DAC5687 DAC A and DAC B outputs can be summed together as shown in Figure 62 to provide a 40-mA full-scale output for increased output power. Figure 62. Combined Output Termination Using a 1:1 Impedance Ratio Transformer Into 50- Ω Load For the case where the digital codes for the two DACs are identical, the termination results in a full-scale swing of 2 VPP into the 50-Ω load, or 10 dBm. This is 6 dB higher than the 4:1 output termination recommended for a single DAC output. There are two methods to produce identical DAC codes. In modes where there is mixing between digital channels A and B, i.e., when channels A and B are isolated, the identical data can be sent to both input ports to produce identical DAC codes. Channels A and B are isolated when FMIX is disabled, the QMC is disabled or enabled with QMC phase register set to 0, and CMIX is disabled or set to fDAC/2. Note that frequency upconversion is still possible using the high-pass filter setting and CMIX fDAC/2. Alternatively, by applying the input data on one input port only and setting the other input port to midscale (zero), the NCO can be used to duplicate the output of the active input channel in the other channel by setting the frequency to zero, phase to 8192 and NCO_GAIN = 1 and QMC gain = 1446. Assuming I(t) is the wanted signal and Q(t) = 0, this is demonstrated by the simplification of the NCO equations in the Fine Mixer (FMIX) section: IOUT(t) = (IIN(t)cos(2π × 0 × t + π/4) – 0 × sin(2π × 0 × t + π/4) × 2 (1 – 1) = I IN(t)cos(π/4) = IIN(t)/2 ½ 54 Submit Documentation Feedback Copyright © 2005–2006, Texas Instruments Incorporated Product Folder Link(s): DAC5687 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |