MPC8536DS datasheet(64/126 Pages) FREESCALE

64 / 126 page

MPC8536E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5

Electrical Characteristics

Freescale Semiconductor

2.11.1

USB DC Electrical Characteristics

This table provides the DC electrical characteristics for the USB interface.

2.11.2

USB AC Electrical Specifications

This table describes the general timing parameters of the USB interface of the chip.

Table 46. USB DC Electrical Characteristics

Parameter

Symbol

Min

Max

Unit

High-level input voltage

VIH

2OVDD + 0.3

Low-level input voltage

VIL

–0.3

0.8

Input current

IIN

—±5

μA

High-level output voltage,

IOH = –100 μA

VOH

OVDD – 0.2

—

Low-level output voltage,

IOL = 100 μA

VOL

—0.2

Note:

1. The symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.

Table 47. USB General Timing Parameters6

Parameter

Symbol 1

Min

Max

Unit

Notes

usb clock cycle time

tUSCK

—

2-5

Input setup to usb clock - all inputs

tUSIVKH

—

2-5

input hold to usb clock - all inputs

tUSIXKH

—

2-5

usb clock to output valid - all outputs

tUSKHOV

—

2-5

Output hold from usb clock - all outputs

tUSKHOX

—

2-5

Notes:

1. The symbols for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs

and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes usb timing (US) for

the input (I) to go invalid (X) with respect to the time the usb clock reference (K) goes high (H). Also, tUSKHOX symbolizes USB

timing (US) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time.

2. All timings are in reference to USB clock.

3. All signals are measured from OVDD/2 of the rising edge of the USB clock to 0.4 × OVDD of the signal in question for 3.3 V

signaling levels.

4. Input timings are measured at the pin.

5. For active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the

component pin is less than or equal to that of the leakage current specification.

6. When switching the data pins from outputs to inputs using the USBn_DIR pin, the output timings will be violated on that cycle

because the output buffers are tristated asynchronously. This should not be a problem, because the PHY should not be

functionally looking at these signals on that cycle as per ULPI specifications

MPC8536DS датащи(PDF) 64 Page - Freescale Semiconductor, Inc

MPC8536DS датащи(HTML) 64 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL