TFP410MPAPREP datasheet(5/31 Pages) TI1

5 / 31 page

TFP410-EP

PanelBus

™ DIGITAL TRANSMITTER

SGLS344A − JULY 2006 − REVISED MAY 2011

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

Terminal Functions (Continued)

TERMINAL

I/O

DESCRIPTION

NAME

NO.

I/O

DESCRIPTION

MSEN/PO1

Monitor sense/programmable output 1. The operation of this pin depends on whether the I2C interface

is enabled or disabled. This pin has an open-drain output and is only 3.3-V tolerant. An external 5-kΩ

pullup resistor connected to VDD is required on this pin.

When I2C is disabled (ISEL = low), a high level indicates a powered-on receiver is detected at the

differential outputs. A low level indicates a powered-on receiver is not detected. This function is valid

only in dc-coupled systems.

When I2C is enabled (ISEL = high), this output is programmable through the I2C interface (see the I2C

Power down (active low). In the power-down state, only the digital I/O buffers and I2C interface remain

active.

When I2C is disabled (ISEL = low), a high level selects the normal operating mode. A low level selects

the power-down mode.

When I2C is enabled (ISEL = high), the power-down state is selected through I2C. In this configuration,

PD should be tied to GND.

Note: The default register value for PD is low, so the device is in power-down mode when I2C is first

enabled or after an I2C reset.

VREF

Input reference voltage. Selects the swing range of the digital data inputs (DATA[23:0], DE, HSYNC,

VSYNC, and IDCK±).

For high-swing 3.3-V input signal levels, VREF should be tied to VDD.

For low-swing input signal levels, VREF should be set to half of the maximum input voltage level. See

the recommended operating conditions section for the allowable range for VREF.

The desired VREF voltage level is typically derived using a simple voltage-divider circuit.

Reserved

RESERVED

This pin is reserved and must be tied to GND for normal operation.

DVI Differential Signal Output

TFADJ

Full-scale adjust. This pin controls the amplitude of the DVI output voltage swing, determined by the

value of the pullup resistor RTFADJ connected to TVDD.

TX0+

TX0−

Channel 0 DVI differential output pair. TX0± transmits the 8-bit blue pixel data during active video and

HSYNC and VSYNC during the blanking interval.

TX1+

TX1−

Channel 1 DVI differential output pair. TX1± transmits the 8-bit green pixel data during active video and

CTL[1] during the blanking interval.

TX2+

TX2−

Channel 2 DVI differential output pair. TX2± transmits the 8-bit red pixel data during active video and

CTL[3:2] during the blanking interval.

TXC+

TXC−

DVI differential output clock

Power and Ground

DGND

16, 48, 64

Ground Digital ground

DVDD

1, 12, 33

Power

Digital power supply. Must be set to 3.3-V nominal.

No connection required. If connected, tie high.

PGND

Ground PLL ground

PVDD

Power

PLL power supply. Must be set to 3.3-V nominal.

TGND

20, 26, 32

Ground Transmitter differential output driver ground

TVDD

23, 29

Power

Transmitter differential output driver power supply. Must be set to 3.3-V nominal.

TFP410MPAPREP датащи(PDF) 5 Page - Texas Instruments

TFP410MPAPREP датащи(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

датащи скачать

ссылки URL