335 datasheet(20/82 Pages) INTEL

20 / 82 page

Datasheet

Electrical Specifications

2.6

FSB Signal Groups

The FSB signals have been combined into groups by buffer type. GTL+ input signals have

differential input buffers that use GTLREF as a reference level. In this document, the term "GTL+

Input" refers to the GTL+ input group as well as the GTL+ I/O group when receiving. Similarly,

"GTL+ Output" refers to the GTL+ output group as well as the GTL+ I/O group when driving.

With the implementation of a source synchronous data bus comes the need to specify two sets of

timing parameters. One set is for common clock signals that are dependent upon the rising edge of

BCLK0 (ADS#, HIT#, HITM#, etc.) and the second set is for the source synchronous signals that

are relative to their respective strobe lines (data and address) as well as the rising edge of BCLK0.

Asychronous signals are still present (A20M#, IGNNE#, etc.) and can become active at any time

during the clock cycle. Table 2-3 identifies which signals are common clock, source synchronous,

and asynchronous.

Table 2-3. FSB Pin Groups

Signal Group

Type

Signals1

NOTES:

Refer to Section 4.2 for signal descriptions.

GTL+ Common Clock

Input

Synchronous to

BCLK[1:0]

BPRI#, DEFER#, RS[2:0]#, RSP#, TRDY#

GTL+ Common Clock

I/O

Synchronous to

BCLK[1:0]

AP[1:0]#, ADS#, BINIT#, BNR#, BPM[5:0]#, BR0#, DBSY#,

DP[3:0]#, DRDY#, HIT#, HITM#, LOCK#, MCERR#

GTL+ Source

Synchronous I/O

Synchronous to

Associated strobe

Signals

Associated Strobe

REQ[4:0]#, A[16:3]#2

ADSTB0#

A[35:17]#2

ADSTB1#

D[15:0]#, DBI0#

DSTBP0#, DSTBN0#

D[31:16]#, DBI1#

DSTBP1#, DSTBN1#

D[47:32]#, DBI2#

DSTBP2#, DSTBN2#

D[63:48]#, DBI3#

DSTBP3#, DSTBN3#

The value of these pins during the active-to-inactive edge of RESET# defines the processor configuration

options. See Section 6.1 for details.

GTL+ Strobes

Synchronous to

BCLK[1:0]

ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#

Asynchronous GTL+

Input

A20M#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, SMI#,

SLP#, STPCLK#, RESET#

Asynchronous GTL+

Output

FERR#/PBE#, IERR#, THERMTRIP#

Asynchronous GTL+

Input/Output

PROCHOT#

TAP Input

Synchronous to TCK

TCK, TDI, TMS, TRST#

TAP Output

Synchronous to TCK

TDO

FSB Clock

Clock

BCLK[1:0], ITP_CLK[1:0]3

In processor systems where there is no debug port implemented on the system board, these signals are used

to support a debug port interposer. In systems with the debug port implemented on the system board, these

signals are no connects.

Power/Other

VCC, VCCA, VCCIOPLL, VID[5:0], VSS, VSSA,

GTLREF[3:0], COMP[1:0], RESERVED, TESTHI[12:0],

THERMDA, THERMDC, VCC_SENSE, VSS_SENSE,

VCCVID, VCCVIDLB, BSEL[1:0], SKTOCC#, DBR#3,

VIDPWRGD, BOOTSELECT, OPTIMIZED/COMPAT#,

PWRGOOD

335 датащи(PDF) 20 Page - Intel Corporation

335 датащи(HTML) 20 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

датащи скачать

ссылки URL