DSP56321 datasheet(16/84 Pages) FREESCALE

16 / 84 page

DSP56321 Technical Data, Rev. 11

1-10

Freescale Semiconductor

Signals/Connections

1.7 Enhanced Synchronous Serial Interface 0 (ESSI0)

Two synchronous serial interfaces (ESSI0 and ESSI1) provide a full-duplex serial port for serial communication

with a variety of serial devices, including one or more industry-standard codecs, other DSPs, microprocessors, and

peripherals that implement the Freescale serial peripheral interface (SPI).

Table 1-11.

Enhanced Synchronous Serial Interface 0

Signal Name

Type

State During

Reset1,2

Signal Description

SC00

PC0

Input or Output

Ignored Input

Serial Control 0—For asynchronous mode, this signal is used for the receive

clock I/O (Schmitt-trigger input). For synchronous mode, this signal is used

either for transmitter 1 output or for serial I/O flag 0.

Port C 0—The default configuration following reset is GPIO input PC0. When

configured as PC0, signal direction is controlled through the Port C Direction

Control Register.

SC01

PC1

Input/Output

Input or Output

Ignored Input

Serial Control 1—For asynchronous mode, this signal is the receiver frame

sync I/O. For synchronous mode, this signal is used either for transmitter 2

output or for serial I/O flag 1.

Port C 1—The default configuration following reset is GPIO input PC1. When

configured as PC1, signal direction is controlled through the Port C Direction

C Control Register.

SC02

PC2

Input/Output

Input or Output

Ignored Input

Serial Control Signal 2—The frame sync for both the transmitter and receiver

in synchronous mode, and for the transmitter only in asynchronous mode. When

configured as an output, this signal is the internally generated frame sync signal.

When configured as an input, this signal receives an external frame sync signal

for the transmitter (and the receiver in synchronous operation).

Port C 2—The default configuration following reset is GPIO input PC2. When

configured as PC2, signal direction is controlled through the Port C Direction

C Control Register.

SCK0

PC3

Input/Output

Input or Output

Ignored Input

Serial Clock—Provides the serial bit rate clock for the ESSI. The SCK0 is a

clock input or output, used by both the transmitter and receiver in synchronous

modes or by the transmitter in asynchronous modes.

Although an external serial clock can be independent of and asynchronous to

the DSP system clock, it must exceed the minimum clock cycle time of 6T (that

is, the system clock frequency must be at least three times the external ESSI

clock frequency). The ESSI needs at least three DSP phases inside each half of

the serial clock.

Port C 3—The default configuration following reset is GPIO input PC3. When

configured as PC3, signal direction is controlled through the Port C Direction

C Control Register.

SRD0

PC4

Input

Input or Output

Ignored Input

Serial Receive Data—Receives serial data and transfers the data to the ESSI

Receive Shift Register. SRD0 is an input when data is received.

Port C 4—The default configuration following reset is GPIO input PC4. When

configured as PC4, signal direction is controlled through the Port C Direction

Port C Control Register.

DSP56321 датащи(PDF) 16 Page - Freescale Semiconductor, Inc

DSP56321 датащи(HTML) 16 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

датащи скачать

ссылки URL