HT45R34 datasheet(11/41 Pages) HOLTEK

11 / 41 page

HT45R34

Rev. 1.20

October 15, 2007

Power Down Operation

The Power Down mode is initialized by the

²HALT² in-

struction and results in the following...

· The system oscillator will be turned off but the WDT

oscillator keeps running, if the internal WDT oscillator

has been selected as the WDT source clock.

· The contents of the on chip RAM and registers remain

unchanged.

· The WDT and WDT prescaler will be cleared and will

resume counting, if the internal WDT oscillator has

been selected as the WDT source clock

· AlloftheI/Oportswillmaintaintheiroriginalstatus.

· The PDF flag is set and the TO flag is cleared.

The system can leave the Power Down mode by means

of an external reset, an interrupt, an external falling

edge signal on port Aor a WDT overflow. An external re-

set causes a device initialisation and the WDT overflow

performs a

²warm reset². After the TO and PDF flags

are examined, the reason for the device reset can be de-

termined. The PDF flag is cleared by a system power-up

or executing the

²CLR WDT² instruction and is set when

²HALT² instruction is executed. The TO flag is set if a

WDT time-out occurs, and causes a wake-up that only

resets the program counter and stack pointer; the other

registers maintain their their original status.

The port A and interrupt methods of wake-up can be

considered as a continuation of normal execution. Each

bit in port A can be independently selected by configura-

tion options to wake-up the device. When awakened

from an I/O port stimulus, the program will resume exe-

cution at the next instruction. If it is awakened due to an

interrupt, two sequences may happen. If the related in-

terrupt is disabled or the interrupt is enabled but the

stack is full, the program will resume execution at the

next instruction. If the interrupt is enabled and the stack

is not full, the regular interrupt response takes place. If

an interrupt request flag is set to

²1² before entering the

Power Down Mode, the wake-up function of the related

interrupt will be disabled. Once a wake-up event occurs,

it takes 1024 tSYS (system clock periods) to resume nor-

mal operation. A dummy period is therefore inserted af-

ter wake-up. If the wake-up results from an interrupt

acknowledgment, the actual interrupt subroutine execu-

tion will be delayed by one or more cycles. If the

wake-up results in the next instruction execution, this

will be executed immediately after the dummy period is

finished.

To minimise power consumption, all the I/O pins should

be carefully managed before entering the Power Down

mode.

Reset

There are three ways in which a reset can occur:

· RES reset during normal operation

· RES reset during HALT

· WDT time-out reset during normal operation

A WDT time-out, when the device is in the Power Down

mode, is different from other device reset conditions, in

that it can perform a

²warm reset² that resets only the

Program Counter and the Stack Poiner, leaving the

other circuits in their original state. Some registers re-

main unchanged during other reset conditions. Most

registers are reset to their

²initial condition² when the re-

set conditions are met. By examining the PDF and TO

flags, the program can distinguish between the different

device reset types.

PDF

RESET Conditions

RES reset during power-up

RES reset during normal operation

RES wake-up HALT

WDT time-out during normal operation

WDT wake-up HALT

Note:

²u² means ²unchanged²

S y s t e m C l o c k / 4

8 - b i t C o u n t e r

W D T P r e s c a l e r

7 - b i t C o u n t e r

8 - t o - 1 M U X

W D T T i m e - o u t

W S 0 ~ W S 2

O p t i o n

S e l e c t

W D T

O S C

Watchdog Timer

HT45R34 датащи(PDF) 11 Page - Holtek Semiconductor Inc

HT45R34 датащи(HTML) 11 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

датащи скачать

ссылки URL