COM20019IP datasheet(76/81 Pages) SMSC

76 / 81 page

DISCONTINUED DATASHEET

APPENDIX A

This appendix describes the function of the

NOSYNC and EF bits.

NOSYNC Bit

The NOSYNC bit controls whether or not the

RAM initialization sequence requires the line to

be idle by enabling or disabling the SYNC

command during initialization. It is defined as

follows:

NOSYNC:

Enable/Disable

SYNC

command

during

initialization.

NOSYNC=0,

Enable

(Default): the line has to be idle for the RAM

initialization sequence to be written, NOSYNC=1,

Disable: the line does not have to be idle for the

RAM initialization sequence to be written.

The following discussion describes the function

of this bit:

During initialization, after the CPU writes the

Node ID, the COM20019 will write "D1"h data to

Address 000h and Node-ID to Address 001h of

its internal RAM within 96uS. These values are

read as part of the diagnostic test. If the D1 and

Node-ID initialization sequence cannot be read,

the initialization routine will report it as a device

diagnostic failure. These writes are controlled by

a micro-program which sometimes waits if the

line is active; SYNC is the micro-program

command that causes the wait. When the micro-

program waits, the initial RAM write does not

occur, which causes the diagnostic error. Thus

in this case, if the line is not idle, the initialization

sequence may not be written, which will be

reported as a device diagnostic failure.

However,

the

initialization

sequence

and

diagnostics

the

COM20019

should

independent of the network status. This is

accomplished through some additional logic to

decode the program counter, enabled by the

NOSYNC bit.

When it finds that the micro-

program is in the initialization routine, it disables

the

SYNC

command.

this

case,

the

initialization will not be held up by the line status.

Thus, by setting the NOSYNC bit, the line does

not have to be idle for the RAM initialization

sequence to be written.

EF Bit

The EF bit controls several modifications to

internal operation timing and logic. It is defined

as follows:

EF: Enable/Disable the new internal operation

timing and logic refinements.

EF=0: (Default)

Disable the new internal operation timing (the

timing is the same as in the COM20020 Rev. B);

EF=1: Enable the new internal operation timing.

The EF bit controls the following timing/logic

refinements in the COM20019:

Extend Interrupt Disable Time

While the interrupt is active (nINTR pin=0), the

interrupt is disabled by writing the Clear Tx/Rx

interrupt and Clear Flag command and by

reading the Next-ID register.

This minimum

disable time is changed by the Data Rate.

Setting the EF bit will change the minimum

disable time to always be more than 200 nS.

This is done by changing the clock which is

supplied to the Interrupt Disable logic. The

frequency of this clock is always less than

20MHz .

Synchronize the Pre-Scalar Output

The Pre-Scalar is used to change the data rate.

The output clock is selected by CKP3-1 bits in

the Set-Up register. The CKP3-1 bits are

changed by writing the Set-Up register from

COM20019IP датащи(PDF) 76 Page - SMSC Corporation

COM20019IP датащи(HTML) 76 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

датащи скачать

ссылки URL