AT43USB326 datasheet(17/102 Pages) ATMEL

17 / 102 page

AT43USB326

3313D–USB–04/06

Functional

Description

On-chip Power

Supply

The AT43USB326 contains two on-chip power supplies that generate 3.3V with a capacity of

30 mA each from the 5V power input. The on-chip power supplies are intended to supply the

AT43USB326 internal circuit and the 1.5K pull-up resistor only and should not be used for

other purposes. External 2.2 µF filter capacitors are required at the power supply outputs,

CEXT1 and CEXT2. The internal power supplies can be disabled as described in the next

paragraph.

The user should be careful when the GPIO pins are required to supply high-load currents. If

the application requires that the GPIO supply currents beyond the capability of the on-chip

power supply, the AT43USB326 should be supplied by an external 3.3V power supply. In this

case, the 5V V

CC power supply pin should be left unconnected and the 3.3V power supplied to

the chip through the CEXT1 and CEXT2 pins.

I/O Pin

Characteristics

The I/O pins of the AT43USB326 should not be directly connected to voltages less than V

SS or

more than the voltage at the CEXT pins. If it is necessary to violate this rule, insert a series

resistor between the I/O pin and the source of the external signal source that limits the current

into the I/O pin to less than 2 mA. Under no circumstance should the external voltage exceed

5.5V. To do so will put the chip under excessive stress.

Oscillator and PLL

All clock signals required to operate the AT43USB326 are derived from an on-chip oscillator.

To reduce EMI and power dissipation, the oscillator is designed to operate with a 6 MHz crys-

tal. An on-chip PLL generates the high frequency for the clock/data separator of the Serial

Interface Engine. In the suspended state, the oscillator circuitry is turned off.

The oscillator of the AT43USB326 is a special, low-drive type, designed to work with most

crystals without any external components. The crystal must be of the parallel resonance type

requiring a load capacitance of about 10 pF. If the crystal requires a higher value capacitance,

external capacitors can be added to the two terminals of the crystal and ground to meet the

required value. To assure quick start-up, a crystal with a high Q, or low ESR, should be used.

To meet the USB hub frequency accuracy and stability requirements for hubs, the crystal

should have an accuracy and stability of better than 100 PPM. The use of a ceramic resonator

in place of the crystal is not recommended because a resonator would not have the necessary

frequency accuracy and stability.

The clock can also be externally sourced. In this case, connect the clock source to the XTAL1

pin, while leaving XTAL2 pin floating. The switching level at the OSC1 pin can be as low as

0.47V and a CMOS device is required to drive this pin to maintain good noise margins at the

low switching level.

For proper operation of the PLL, an external RC filter consisting of a series RC network of

100

Ω and 0.1 µF in parallel with a 0.01 µF capacitor must be connected from the LFT pin to

SS. Use only high-quality ceramic capacitors.

AT43USB326 датащи(PDF) 17 Page - ATMEL Corporation

AT43USB326 датащи(HTML) 17 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL