WM8976 datasheet(22/83 Pages) WOLFSON

22 / 83 page

WM8976

Preliminary Technical Data

PTD Rev 2.0 February 2005

DEVICE DESCRIPTION

INTRODUCTION

The WM8976 is a low power audio codec combining a high quality stereo audio DAC and mono

ADC, with flexible line and microphone input and output processing. Applications for this device

include digital camcorders, and digital still cameras with mono record and mono or stereo playback

capability.

FEATURES

The chip offers great flexibility in use, and so can support many different modes of operation as

follows:

MICROPHONE INPUT

A microphone pre-amp is provided, allowing for a microphone to be pseudo-differentially connected,

with user-defined gain using internal resistors. The provision of the common mode input pin allows

for rejection of common mode noise on the microphone input (Level depends on gain setting

chosen). A microphone bias is output from the chip which can be used to bias the microphone. The

signal routing can be configured to allow manual adjustment of mic level, or indeed to allow the ALC

loop to control the level of mic signal that is transmitted.

Total gain through the microphone path of up to +55.25dB can be selected.

PGA AND ALC OPERATION

A programmable gain amplifier is provided in the input path to the ADC. This may be used manually

or in conjunction with a mixed analogue/digital automatic level control (ALC) which keeps the

recording volume constant.

LINE INPUTS (AUXL, AUXR)

The inputs, AUXL and AUXR, can be used as a stereo line input or as an input for warning tones (or

‘beeps’) etc. The AUXL input can be summed into the record path, along with the microphone

preamp output.

ADC

The ADC uses a multi-bit high-order oversampling architecture to deliver optimum performance with

low power consumption.

HI-FI DAC

The stereo hi-fi DAC provides high quality audio playback suitable for all portable audio hi-fi type

applications, including MP3 players and portable disc players of all types.

OUTPUT MIXERS

Flexible mixing is provided on the outputs of the device. A stereo mixer is provided for the stereo

headphone or line outputs, LOUT1/ROUT1, and additional summers on the OUT3/OUT4 outputs

allow for an optional differential or stereo line output on these pins. Gain adjustment PGAs are

provided for the LOUT1/ROUT1 and LOUT2/ROUT2 outputs, and signal switching is provided to

allow for all possible signal combinations. The output buffers can be configured in several ways,

allowing support of up to three sets of external transducers; ie stereo headphone, BTL speaker, and

BTL earpiece may be connected simultaneously. Thermal implications should be considered before

simultaneous full power operation of all outputs is attempted.

Alternatively, if a speaker output is not required, the LOUT2 and ROUT2 pins might be used as a

stereo headphone driver, (disable output invert buffer on ROUT2). In that case two sets of

headphones might be driven, or the LOUT2 and ROUT2 pins used as a line output driver.

WM8976 датащи(PDF) 22 Page - Wolfson Microelectronics plc

WM8976 датащи(HTML) 22 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

датащи скачать

ссылки URL