| поискавой системы для электроныых деталей |
|
PC97338 датащи(PDF) 190 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
PC97338 датащи(HTML) 190 Page - National Semiconductor (TI) |
|
190 / 221 page ![]() 190 www.national.com 6.0 DMA and Interrupt Mapping The Chip provides Plug and Play support. 6.1 DMA SUPPORT 6.1.1 Legacy Mode Table 98 shows the conditions under which DMA re- quest signals are put in TRI-STATE, in legacy mode. For each DMA signal to be put in TRI-STATE, every column must have one true condition. If no condition is true in any one column, the signal is not put in TRI- STATE. 6.1.2 Plug and Play Mode The Chip allows the Floppy Disk Controller (FDC), the parallel port and SCC2 to be connected to three 8-bit DMA channels. It is illegal to configure a pair of DMA signals to more than one DMA source. A pair of DMA signals may be configured to a specific device only when the device is disabled. Upon reset, DRQ2 and DACK2 are used by the FDC. A DRQ line is in TRI-STATE and the DACK line input is blocked to 1, when any of the following conditions is true: • When no device is mapped to the DMA channel. • When the device mapped to the DMA channel is inactive. In Plug and Play mode, this condition is true for all devices. In Legacy mode, this condition is true only for SCC2 and the parallel port, controlled by bit 2 of the FER register and bit 2 of the PCR register, re- spectively. • When the device mapped to the DMA channel floats its DRQ line. Table 99 shows the conditions that put DMA request signals in TRI-STATE, in Plug and Play mode. For each DMA signal to be put in TRI-STATE, every col- umn must have one true condition. If no condition is true in any one column, the signal is not put in TRI- STATE. TABLE 98. DMA Support in Legacy Mode TABLE 99. DMA Support in Plug and Play Mode DMA Signal Conditions for DRQx a to be in TRI-STATE Parallel Port FDC SCC2 DRQx a a. x = 0, 1 or 2 DRQx a not selected or bit 2 of PCR = 0 or bit 2 of PCR = 1 and bit 3 of ECR =0 DRQx a not selected or bit 3 of DOR = 0 and bit 7 of ASC = 1 DRQx a not selected or bit 2 of FER. = 0 DMA Signal Conditions for DRQx a to be in TRI-STATE Parallel Port FDC SCC2 DRQx a a. x = 0, 1 or 2 DRQx a not selected or bit 0 of FER = 0 or bit 2 of PCR = 0 or bit 2 of PCR = 1 and bit 3 of ECR =0 DRQx a not selected or bit 3 of FER = 0 or bit 3 of DOR = 0 and bit 7 of ASC = 1 DRQx a not selected or bit 2 of FER = 0 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |