HT46C22 datasheet(10/46 Pages) HOLTEK

10 / 46 page

HT46R22/HT46C22

Rev. 1.10

October 2, 2002

All these kinds of interrupts have a wake-up capability.

As an interrupt is serviced, a control transfer occurs by

pushing the program counter onto the stack, followed by

a branch to a subroutine at specified location in the pro-

gram memory. Only the program counter is pushed onto

the stack. If the contents of the register or status register

(STATUS) are altered by the interrupt service program

which corrupts the desired control sequence, the con-

tents should be saved in advance.

External interrupts are triggered by a high to low transi-

tion of INT and the related interrupt request flag (EIF; bit

4 of INTC0) will be set. When the interrupt is enabled,

the stack is not full and the external interrupt is active, a

subroutine call to location 04H will occur. The interrupt

request flag (EIF) and EMI bits will be cleared to disable

other interrupts.

The internal timer/event counter interrupt is initialized by

setting the timer/event counter interrupt request flag

(TF; bit 5 of INTC0), caused by a timer overflow. When

the interrupt is enabled, the stack is not full and the TF

bit is set, a subroutine call to location 08H will occur. The

related interrupt request flag (TF) will be reset and the

EMI bit cleared to disable further interrupts.

The A/D converter interrupt is initialized by setting the

A/D converter request flag (ADF; bit 6 of INTC0),

caused by an end of A/D conversion. When the interrupt

is enabled, the stack is not full and the ADF is set, a sub-

routine call to location 0CH will occur. The related inter-

rupt request flag (ADF) will be reset and the EMI bit

cleared to disable further interrupts.

Function

INTC0

(0BH)

EMI

Controls the master (global)

interrupt

(1= enabled; 0= disabled)

EEI

Controls the external interrupt

(1= enabled; 0= disabled)

ETI

Controls the timer/event

counter interrupt

(1= enabled; 0= disabled)

EADI

Controls the A/D converter

interrupt

(1= enabled; 0= disabled)

EIF

External interrupt request flag

(1= active; 0= inactive)

5TF

Internal timer/event counter

request flag

(1= active; 0= inactive)

ADF

A/D converter request flag

(1= active; 0= inactive)

Unused bit, read as

²0²

INTC0 register

The I

2C BUS interrupt is initialized by setting the I2C

BUS interrupt request flag (HIF; bit 4 of INTC1), caused

by a slave address match (HAAS=

²1²) or 1 byte of data

transfer is completed. When the interrupt is enabled, the

stack is not full and the HIF bit is set, a subroutine call to lo-

cation 10H will occur. The related interrupt request flag

(HIF) will be reset and the EMI bit cleared to disable further

interrupts.

During the execution of an interrupt subroutine, other in-

terrupt acknowledgments are held until the

²RETI² in-

struction is executed or the EMI bit and the related

interrupt control bit are set to 1 (of course, if the stack is

not full). To return from the interrupt subroutine,

²RET² or

²RETI² may be invoked. RETI will set the EMI bit to en-

able an interrupt service, but RET will not.

Interrupts, occurring in the interval between the rising

edges of two consecutive T2 pulses, will be serviced on

the latter of the two T2 pulses, if the corresponding inter-

rupts are enabled. In the case of simultaneous requests

the following table shows the priority that is applied.

These can be masked by resetting the EMI bit.

No.

Interrupt Source

Priority Vector

External Interrupt

04H

Timer/Event Counter Overflow

08H

A/D Converter Interrupt

0CH

2C BUS Interrupt

10H

The timer/event counter interrupt request flag (TF), ex-

ternal interrupt request flag (EIF), A/D converter request

flag (ADF), the I

2C BUS interrupt request flag (HIF), en-

able timer/event counter bit (ETI), enable external inter-

rupt bit (EEI), enable A/D converter interrupt bit (EADI),

enable I

2C BUS interrupt bit (EHI) and enable master in-

terrupt bit (EMI) constitute an interrupt control register 0

(INTC0) and an interrupt control register 1 (INTC1)

which are located at 0BH and 1EH in the data memory.

EMI, EEI, ETI, EADI, EHI are used to control the en-

abling/disabling of interrupts. These bits prevent the re-

quested interrupt from being serviced. Once the

interrupt request flags (TF, EIF, ADF, HIF) are set, they

will remain in the INTC0 and INTC1 register until the in-

terrupts are serviced or cleared by a software instruc-

tion.

Function

INTC1

(1EH)

EHI

Controls the I

2C BUS inter-

rupt (1=enabled; 0=disabled)

Unused bit, read as

²0²

Unused bit, read as

²0²

Unused bit, read as

²0²

HIF

2C BUS interrupt request

flag (1=active; 0=inactive)

Unused bit, read as

²0²

Unused bit, read as

²0²

Unused bit, read as

²0²

INTC1 register

HT46C22 датащи(PDF) 10 Page - Holtek Semiconductor Inc

HT46C22 датащи(HTML) 10 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

датащи скачать

ссылки URL