S29GL01GS datasheet(74/106 Pages) SPANSION

74 / 106 page

GL-S MirrorBit® Family

S29GL_128S_01GS_00_08 October 9, 2013

Da ta

Sh e e t

9.4

DC Characteristics

Notes:

1. ICC active while Embedded Algorithm is in progress.

2. Not 100% tested.

3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.

4. VIO = 1.65V to VCC or 2.7V to VCC depending on the model.

5. VCC = 3V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at >1.8V.

6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes

correctly.

7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification

until the embedded operation is stopped by the reset. If no embedded operation is in progress when reset is started, or following the

stopping of an embedded operation, ICC5 will be drawn during the remainder of tRPH. After the end of tRPH the device will go to standby

mode until the next read or write.

8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.

Table 9.3 DC Characteristics (-40°C to +85°C)

Parameter

Description

Test Conditions

Min

Typ

(Note 2)

Max

Unit

ILI

Input Load Current

VIN = VSS to VCC, VCC = VCC max

+0.02

±1.0

µA

ILO

Output Leakage Current

VOUT = VSS to VCC, VCC = VCC max

+0.02

±1.0

µA

ICC1

VCC Active Read Current

CE# = VIL, OE# = VIH, Address

switching@ 5 MHz, VCC = VCC max

ICC2

VCC Intra-Page Read Current

CE# = VIL, OE# = VIH, Address

switching@ 33 MHz, VCC = VCC max

925

ICC3

VCC Active Erase/Program

Current (Notes 1, 2)

CE# = VIL, OE# = VIH, VCC = VCC max

100

ICC4

VCC Standby Current

CE#, RESET#, OE# = VIH, VIH = VIO

VIL = VSS, VCC = VCC max

100

µA

ICC5

VCC Reset Current (Notes 2, 7)

CE# = VIH, RESET# = VIL,

VCC = VCC max

ICC6

Automatic Sleep Mode (Note 3)

VIH = VIO, VIL = VSS ,

VCC = VCC max, tACC + 30 ns

VIH = VIO, VIL = VSS,

VCC = VCC max, tASSB

100

150

µA

ICC7

VCC Current during power up

(Notes 2, 6)

RESET# = VIO, CE# = VIO, OE# = VIO,

VCC = VCC max,

VIL

Input Low Voltage (Note 4)

-0.5

0.3 x VIO

VIH

Input High Voltage (Note 4)

0.7 x VIO

VIO + 0.4

VOL

Output Low Voltage (Notes 4, 8)

IOL = 100 µA for DQ15-DQ0;

IOL = 2 mA for RY/BY#

0.15 x VIO

VOH

Output High Voltage (Note 4)

IOH = 100 µA

0.85 x VIO

VLKO

Low VCC Lock-Out Voltage

(Note 2)

2.25

2.5

VRST

Low VCC Power on Reset Voltage

(Note 2)

1.0

S29GL01GS датащи(PDF) 74 Page - SPANSION

S29GL01GS датащи(HTML) 74 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL