COM20020ILJP datasheet(33/72 Pages) MICROCHIP

33 / 72 page

5Mbps ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM

Datasheet

SMSC COM20020I Rev D

Page 33

Revision 12-05-06

DATASHEET

Table 6.5 - Command Register

DATA

COMMAND

DESCRIPTION

0000 0000

Clear

Transmit

Interrupt

This command is used only in the Command Chaining operation. Please

refer to the Command Chaining section for definition of this command.

0000 0001

Disable

Transmitter

This command will cancel any pending transmit command (transmission

that has not yet started) and will set the TA (Transmitter Available) status

bit to logic "1" when the COM20020ID next receives the token.

0000 0010

Disable

Receiver

This command will cancel any pending receive command. If the

COM20020ID is not yet receiving a packet, the RI (Receiver Inhibited) bit

will be set to logic "1" the next time the token is received. If packet

reception is already underway, reception will run to its normal

conclusion.

b0fn n100

Enable

Receive to

Page fnn

This command allows the COM20020ID to receive data packets into

RAM buffer page fnn and resets the RI status bit to logic "0". The values

placed in the "nn" bits indicate the page that the data will be received

into (page 0, 1, 2, or 3). If the value of "f" is a logic "1", an offset of 256

bytes will be added to that page specified in "nn", allowing a finer

resolution of the buffer. Refer to the Selecting RAM Page Size section

for further detail. If the value of "b" is logic "1", the device will also

receive broadcasts (transmissions to ID zero). The RI status bit is set to

logic "1" upon successful reception of a message.

00fn n011

Enable

Transmit from

Page fnn

This command prepares the COM20020ID to begin a transmit sequence

from RAM buffer page fnn the next time it receives the token. The

values of the "nn" bits indicate which page to transmit from (0, 1, 2, or 3).

If "f" is logic "1", an offset of 256 bytes is the start of the page specified in

"nn", allowing a finer resolution of the buffer. Refer to the Selecting RAM

Page Size section for further detail. When this command is loaded, the

TA and TMA bits are reset to logic "0". The TA bit is set to logic "1" upon

completion of the transmit sequence. The TMA bit will have been set by

this time if the device has received an ACK from the destination node.

The ACK is strictly hardware level, sent by the receiving node before its

microcontroller is even aware of message reception. Refer to Figure 3.1

for details of the transmit sequence and its relation to the TA and TMA

status bits.

0000 c101

Define

Configuration

This command defines the maximum length of packets that may be

handled by the device. If "c" is a logic "1", the device handles both long

and short packets. If "c" is a logic "0", the device handles only short

packets.

000r p110

Clear Flags

This command resets certain status bits of the COM20020ID. A logic "1"

on "p" resets the POR status bit and the EXCNAK Diagnostic status bit.

A logic "1" on "r" resets the RECON status bit.

0000 1000

Clear

Receive

Interrupt

This command is used only in the Command Chaining operation. Please

refer to the Command Chaining section for definition of this command.

0001 1000

Start Internal

Operation

This command restarts the stopped internal operation after changing

CKUP1 or CKUP0 bit.

COM20020ILJP датащи(PDF) 33 Page - Microchip Technology

COM20020ILJP датащи(HTML) 33 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

датащи скачать

ссылки URL