 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
PIC12F635ESS датащи(PDF) 171 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC12F635ESS датащи(HTML) 171 Page - Microchip Technology |
|
|
171 / 234 page  © 2007 Microchip Technology Inc. DS41232D-page 169 PIC12F635/PIC16F636/639 15.3 DC Characteristics: PIC12F635/PIC16F636-E (Extended) DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated) Operating temperature -40 °C ≤ TA ≤ +125°C for extended Param No. Sym Device Characteristics Min Typ† Max Units Conditions VDD Note D010E IDD Supply Current(1,2) —11 16 μA2.0 FOSC = 32.768 kHz LP Oscillator mode —18 28 μA3.0 —35 54 μA5.0 D011E — 140 240 μA2.0 FOSC = 1 MHz XT Oscillator mode — 220 380 μA3.0 — 380 550 μA5.0 D012E — 260 360 μA2.0 FOSC = 4 MHz XT Oscillator mode — 420 650 μA3.0 — 0.8 1.1 mA 5.0 D013E — 130 220 μA2.0 FOSC = 1 MHz EC Oscillator mode — 215 360 μA3.0 — 360 520 μA5.0 D014E — 220 340 μA2.0 FOSC = 4 MHz EC Oscillator mode — 375 550 μA3.0 — 0.65 1.0 mA 5.0 D015E — 820 μA2.0 FOSC = 31 kHz LFINTOSC mode — 16 40 μA3.0 — 31 65 μA5.0 D016E — 340 450 μA2.0 FOSC = 4 MHz HFINTOSC mode — 500 700 μA3.0 — 0.8 1.2 mA 5.0 D017E — 410 650 μA2.0 FOSC = 8 MHz HFINTOSC mode — 700 950 μA3.0 — 1.30 1.65 mA 5.0 D018E — 230 100 μA2.0 FOSC = 4 MHz EXTRC mode — 400 680 μA3.0 — 0.63 1.1 mA 5.0 D019E — 2.6 3.25 mA 4.5 FOSC = 20 MHz HS Oscillator mode — 2.8 3.35 mA 5.0 † Data in “Typ” column is at 5.0V, 25 °C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The test conditions for all IDD measurements in Active Operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. 3: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this periph- eral is enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD current from this limit. Max values should be used when calculating total current consumption. 4: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
