| поискавой системы для электроныых деталей |
|
DS32EL0421 датащи(PDF) 13 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
DS32EL0421 датащи(HTML) 13 Page - Texas Instruments |
|
13 / 32 page ![]() IDLE LINK DETECT LINK ACQUISITION NORMAL TxCLKIN exist Link Detect fail TxCLKIN does not exist Power-On/Reset RS: 1, DC_B: 0 RS: 1, DC_B: 1 DS32EL0421, DS32ELX0421 www.ti.com SNLS282F – MAY 2008 – REVISED APRIL 2013 Figure 7. Serializer State Diagram SCRAMBLER and NRZI Encoder The CDR of the DS32EL0124 and the DS32ELX0124 expect a transition density of 20% for a period of 200 μs. If the scrambler and NRZI encoder are enabled, the raw or DC-balanced serialized data is scrambled to improve transition density. The scrambler accepts 20 bits of data and encodes it using the polynomial X9 + X4 + 1. The data can then be sent to the NRZ-to-NRZI converter before being output. Enabling the scrambler can help to lower EMI emissions by spreading the spectrum of the data. Scrambling also creates transitions for the deserializer’s CDR to properly lock onto. The scrambler and NRZI encoder are enabled or disabled by default depending on how the DC_B and RS pins are configured. To override the default scrambler setting two register writes must be performed. First, write to register 22’h and set bit 3 to unlock the scrambler register. Next write to register 21’h and change bit 4 to the desired value. The NRZI encoder can be enabled or disabled independently of the scrambler by controlling bit 7 of register 21'h and bit 4 of register 22'h. CML OUTPUT DATA INTERFACING The serial outputs provide low-skew differential signals. Internal resistors connected from TxOUTn+ and TxOUTn- to VDD25 terminate the outputs. The output level can be programmed by adjusting the pull-down resistor to the VOD_CTRL pin. The output terminations can also be programmed to be either 50 Ω or 75 Ω. The output buffer consists of a current mode logic (CML) driver with user configurable de-emphasis control, which can be used to optimize performance over a wide range of transmission line lengths and attenuation distortions resulting from low cost CAT(-5, -6, -7) cable or FR–4 backplane. Output de-emphasis is user programmable through either device pins DE_EMPH0 and DE_EMPH1 or SMBus interface. Users can control the strength of the de-emphasis to optimize for a specific system environment. Please see Table 1 for details. Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 13 Product Folder Links: DS32EL0421 DS32ELX0421 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |