| поискавой системы для электроныых деталей |
|
SAM3X датащи(PDF) 19 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
SAM3X датащи(HTML) 19 Page - ATMEL Corporation |
|
19 / 71 page ![]() 21 11057BS–ATARM–13-Jul-12 SAM3X/A 21 11057BS–ATARM–13-Jul-12 SAM3X/A 5. Power Considerations 5.1 Power Supplies The SAM3X/A series product has several types of power supply pins: • VDDCORE pins: Power the core, the embedded memories and the peripherals; voltage ranges from 1.62V to 1.95V. • VDDIO pins: Power the Peripherals I/O lines; voltage ranges from 1.62V to 3.6V. • VDDIN pin: Powers the Voltage regulator • VDDOUT pin: It is the output of the voltage regulator. • VDDBU pin: Powers the Slow Clock oscillator and a part of the System Controller; voltage ranges from 1.62V to 3.6V. VDDBU must be supplied before or at the same time than VDDIO and VDDCORE. • VDDPLL pin: Powers the PLL A, UPLL and 3-20 MHz Oscillator; voltage ranges from 1.62V to 1.95V. • VDDUTMI pin: Powers the UTMI+ interface; voltage ranges from 3.0V to 3.6V, 3.3V nominal. • VDDANA pin: Powers the ADC and DAC cells; voltage ranges from 2.0V to 3.6V. Ground pins GND are common to VDDCORE and VDDIO pins power supplies. Separated ground pins are provided for VDDBU, VDDPLL, VDDUTMI and VDDANA. These ground pins are respectively GNDBU, GNDPLL, GNDUTMI and GNDANA. 5.2 Voltage Regulator The SAM3X/A series embeds a voltage regulator that is managed by the Supply Controller. This internal regulator is intended to supply the internal core of SAM3X/A series but can be used to supply other parts in the application. It features two different operating modes: • In Normal mode, the voltage regulator consumes less than 700 µA static current and draws 150 mA of output current. Internal adaptive biasing adjusts the regulator quiescent current depending on the required load current. In Wait Mode or when the output current is low, quiescent current is only 7µA. • In Shutdown mode, the voltage regulator consumes less than 1 µA while its output is driven internally to GND. The default output voltage is 1.80V and the start-up time to reach Normal mode is inferior to 400 µs. For adequate input and output power supply decoupling/bypassing, refer to “Voltage Regulator” in the “Electrical Characteristics” section of the product datasheet. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |