ADS5281IPFPR datasheet(30/44 Pages) TI

30 / 44 page

www.ti.com

APPLICATION INFORMATION

THEORY OF OPERATION

ANALOG INPUT

ADS5281

ADS5282

SBAS397H – DECEMBER 2006 – REVISED MARCH 2008

The ADC output goes to a serializer that operates

from a 12x clock generated by the PLL. The 12 data

bits from each channel are serialized and sent LSB

The ADS528x devices are a family of 8-channel,

first. In addition to serializing the data, the serializer

high-speed, CMOS ADCs. The 12 bits given out by

also generates a 1x clock and a 6x clock. These

each channel are serialized and sent out on a single

clocks are generated in the same way the serialized

pair of pins in LVDS format. All eight channels of the

data are generated, so these clocks maintain perfect

ADS528x operate from a single clock (ADCLK). The

synchronization with the data. The data and clock

sampling clocks for each of the eight channels are

outputs of the serializer are buffered externally using

generated from the input clock using a carefully

LVDS buffers. Using LVDS buffers to transmit data

matched clock buffer tree. The 12x clock required for

externally has multiple advantages, such as a

the serializer is generated internally from ADCLK

reduced number of output pins (saving routing space

using a phase-locked loop (PLL). A 6x and a 1x clock

on the board), reduced power consumption, and

are also output in LVDS format, along with the data,

reduced effects of digital noise coupling to the analog

to enable easy data capture. The ADS528x operates

circuit inside the ADS528x.

from internally-generated reference voltages that are

trimmed to improve to a high level of accuracy.

The ADS528x operates from two sets of supplies and

Trimmed references improve the gain matching

grounds. The analog supply and ground set is

across devices, and provide the option to operate the

identified as AVDD and AVSS, while the digital set is

devices without having to externally drive and route

identified by LVDD and LVSS.

reference lines. The nominal values of REFT and

REFB

are

2.5V

and

0.5V,

respectively.

The

references are internally scaled down differentially by

a factor of 2. This scaling results in a differential input

The analog input consists of a switched-capacitor

of –1V to correspond to the zero code of the ADC,

based, differential sample-and-hold architecture. This

and a differential input of +1V to correspond to the

differential

topology

results

very

good

full-scale code (4095 LSB). VCM (the common-mode

performance even for high input frequencies at high

voltage of REFT and REFB) is also made available

sampling rates. The INN and INP pins must be

externally through a pin, and is nominally 1.5V.

externally biased around a common-mode voltage of

1.5V, available on VCM. For a full-scale differential

The ADC employs a pipelined converter architecture

input, each input pin (INN and INP) must swing

that consists of a combination of multi-bit and

symmetrically between VCM + 0.5V and VCM – 0.5V,

single-bit internal stages. Each stage feeds its data

resulting in a 2VPP differential input swing. The

into

the

digital

error

correction

logic,

ensuring

maximum input peak-to-peak differential swing is

excellent differential linearity and no missing codes at

determined to be the difference between the internal

the 12-bit level.

reference voltages REFT (2.5V nominal) and REFB

(0.5V nominal). Figure 34 illustrates the model of the

input driving circuit.

Submit Documentation Feedback

Product Folder Link(s): ADS5281 ADS5282

ADS5281IPFPR датащи(PDF) 30 Page - Texas Instruments

ADS5281IPFPR датащи(HTML) 30 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

датащи скачать

ссылки URL