PIC18F23K20-ESLASHML datasheet(144/456 Pages) MICROCHIP

144 / 456 page

PIC18F2XK20/4XK20

DS41303G-page 144

 2010 Microchip Technology Inc.

11.1

CCP Module Configuration

Each Capture/Compare/PWM module is associated

with a control register (generically, CCPxCON) and a

data register (CCPRx). The data register, in turn, is

comprised of two 8-bit registers: CCPRxL (low byte)

and CCPRxH (high byte). All registers are both

readable and writable.

11.1.1

CCP MODULES AND TIMER

RESOURCES

The CCP modules utilize Timers 1, 2 or 3, depending

on the mode selected. Timer1 and Timer3 are available

to modules in Capture or Compare modes, while

Timer2 is available for modules in PWM mode.

TABLE 11-1:

CCP MODE – TIMER

RESOURCE

The assignment of a particular timer to a module is

determined by the Timer-to-CCP enable bits in the

T3CON register (Register 15-1). Both modules can be

active at the same time and can share the same timer

resource if they are configured to operate in the same

mode (Capture/Compare or PWM). The interactions

between the two modules are summarized in Figure 11-1

and Figure 11-2. In Asynchronous Counter mode, the

capture operation will not work reliably.

11.1.2

CCP2 PIN ASSIGNMENT

The pin assignment for CCP2 (Capture input, Compare

and PWM output) can change, based on device config-

uration. The CCP2MX Configuration bit determines the

pin with which CCP2 is multiplexed. By default, it is

assigned to RC1 (CCP2MX = 1). If the Configuration bit

is cleared, CCP2 is multiplexed with RB3.

Changing the pin assignment of CCP2 does not

automatically change any requirements for configuring

the port pin. Users must always verify that the

appropriate TRIS register is configured correctly for

CCP2 operation, regardless of where it is located.

TABLE 11-2:

INTERACTIONS BETWEEN CCP1 AND CCP2 FOR TIMER RESOURCES

CCP/ECCP Mode

Timer Resource

Capture

Timer1 or Timer3

Compare

Timer1 or Timer3

PWM

Timer2

CCP1 Mode CCP2 Mode

Interaction

Capture

Each module can use TMR1 or TMR3 as the time base. The time base can be different

for each CCP.

Capture

Compare

CCP2 can be configured for the Special Event Trigger to reset TMR1 or TMR3

(depending upon which time base is used). Automatic A/D conversions on trigger event

can also be done. Operation of CCP1 could be affected if it is using the same timer as a

time base.

Compare

Capture

CCP1 can be configured for the Special Event Trigger to reset TMR1 or TMR3

(depending upon which time base is used). Operation of CCP2 could be affected if it is

using the same timer as a time base.

Compare

Either module can be configured for the Special Event Trigger to reset the time base.

Automatic A/D conversions on CCP2 trigger event can be done. Conflicts may occur if

both modules are using the same time base.

Capture

PWM

None

Compare

PWM

None

PWM(1)

Capture

None

PWM(1)

Compare

None

PWM(1)

PWM

Both PWMs will have the same frequency and update rate (TMR2 interrupt).

Note 1:

Includes standard and enhanced PWM operation.

PIC18F23K20-E/ML датащи(PDF) 144 Page - Microchip Technology

PIC18F23K20-E/ML датащи(HTML) 144 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL