| поискавой системы для электроныых деталей |
|
HT68F20 датащи(PDF) 96 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT68F20 датащи(HTML) 96 Page - Holtek Semiconductor Inc |
|
96 / 210 page ![]() HT68F20/HT68F30/HT68F40/HT68F50/HT68F60 Rev.1.00 96 November 3, 2009 · 16-bit Standard TM Register List - HT68F40/HT68F50/HT68F60 ¨ TM2C0 Register - 16-bit STM Bit 76543210 Name T2PAU T2CK2 T2CK1 T2CK0 T2ON ¾¾¾ R/W R/W R/W R/W R/W R/W ¾¾¾ POR 00000 ¾¾¾ Bit 7 T2PAU: TM2 Counter Pause Control 0: Run 1: Pause The counter can be paused by setting this bit high. Clearing the bit to zero restores normal counter operation. When in a Pause condition the TM will remain powered up and continue to consume power. The counter will retain its residual value when this bit changes from low to high and resume counting from this value when the bit changes to a low value again. Bit 6~4 T2CK2, T2CK1, T2CK0: Select TM2 Counter clock 000: fSYS/4 001: fSYS 010: fH/16 011: fH/64 100: fTBC 101: Reserved 110: TCK2 rising edge clock 111: TCK2 falling edge clock These three bits are used to select the clock source for the TM. Selecting the Reserved clock input will effectively disable the internal counter. The external pin clock source can be chosen to be active on the rising or falling edge. The clock source fSYS is the system clock, while fH and fTBC are other internal clocks, the details of which can be found in the oscillator section. Bit 3 T2ON: TM2 Counter On/Off Control 0: Off 1: On This bit controls the overall on/off function of the TM. Setting the bit high enables the counter to run, clearing the bit disables the TM. Clearing this bit to zero will stop the counter from counting and turn off the TM which will reduce its power consumption. When the bit changes state from low to high the internal counter value will be reset to zero, however when the bit changes from high to low, the internal counter will retain its residual value until the bit returns high again. If the TM is in the Compare Match Output Mode then the TM output pin will be reset to its initial condition, as specified by the T2OC bit, when the T2ON bit changes from low to high. Bit 2~0 Unimplemented, read as ²0² |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |