ATmega328P datasheet(115/448 Pages) ATMEL

115 / 448 page

115

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

put Compare Units” on page 122. The compare match event will also set the Compare Match

Flag (OCF1A/B) which can be used to generate an Output Compare interrupt request.

The Input Capture Register can capture the Timer/Counter value at a given external (edge trig-

gered) event on either the Input Capture pin (ICP1) or on the Analog Comparator pins (See

”Analog Comparator” on page 246) The Input Capture unit includes a digital filtering unit (Noise

Canceler) for reducing the chance of capturing noise spikes.

The TOP value, or maximum Timer/Counter value, can in some modes of operation be defined

by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When using

OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for generating a

PWM output. However, the TOP value will in this case be double buffered allowing the TOP

value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can be used

as an alternative, freeing the OCR1A to be used as PWM output.

15.2.2

Definitions

The following definitions are used extensively throughout the section:

15.3

Accessing 16-bit Registers

The TCNT1, OCR1A/B, and ICR1 are 16-bit registers that can be accessed by the AVR CPU via

the 8-bit data bus. The 16-bit register must be byte accessed using two read or write operations.

Each 16-bit timer has a single 8-bit register for temporary storing of the high byte of the 16-bit

access. The same temporary register is shared between all 16-bit registers within each 16-bit

timer. Accessing the low byte triggers the 16-bit read or write operation. When the low byte of a

16-bit register is written by the CPU, the high byte stored in the temporary register, and the low

byte written are both copied into the 16-bit register in the same clock cycle. When the low byte of

a 16-bit register is read by the CPU, the high byte of the 16-bit register is copied into the tempo-

rary register in the same clock cycle as the low byte is read.

Not all 16-bit accesses uses the temporary register for the high byte. Reading the OCR1A/B 16-

bit registers does not involve using the temporary register.

To do a 16-bit write, the high byte must be written before the low byte. For a 16-bit read, the low

byte must be read before the high byte.

The following code examples show how to access the 16-bit Timer Registers assuming that no

interrupts updates the temporary register. The same principle can be used directly for accessing

the OCR1A/B and ICR1 Registers. Note that when using “C”, the compiler handles the 16-bit

access.

BOTTOM

The counter reaches the BOTTOM when it becomes 0x0000.

MAX

The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65535).

TOP

The counter reaches the TOP when it becomes equal to the highest value in the count

sequence. The TOP value can be assigned to be one of the fixed values: 0x00FF, 0x01FF,

or 0x03FF, or to the value stored in the OCR1A or ICR1 Register. The assignment is

dependent of the mode of operation.

ATmega328P датащи(PDF) 115 Page - ATMEL Corporation

ATmega328P датащи(HTML) 115 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL