| поискавой системы для электроныых деталей |
|
MCP4017 датащи(PDF) 36 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP4017 датащи(HTML) 36 Page - Microchip Technology |
|
36 / 66 page ![]() MCP4017/18/19 DS22147A-page 36 © 2009 Microchip Technology Inc. 5.2.9 I2C COMMAND PROTOCOL The MCP4017/18/19 is a slave I2C device which supports 7-bit slave addressing. The slave address contains seven fixed bits. Figure 5-9 shows the control byte format. 5.2.9.1 Control Byte (Slave Address) The Control Byte is always preceded by a START condition. The Control Byte contains the slave address consisting of seven fixed bits and the R/W bit. Figure 5- 9 shows the control byte format and Table 5-2 shows the I2C address for the devices. FIGURE 5-9: Slave Address Bits in the I2C Control Byte. TABLE 5-2: DEVICE I2C ADDRESS 5.2.9.2 Hardware Address Pins The MCP4017/MCP4018/MCP4019 does not support hardware address bits. 5.2.10 GENERAL CALL The General Call is a method that the Master device can communicate with all other Slave devices. The MCP4017/18/19 devices do not respond to General Call address and commands, and therefore the communications are Not Acknowledged. FIGURE 5-10: General Call Formats. SA6 A5A4A3A2 A1A0 R/W A/A Start bit Slave Address R/W bit A bit (controlled by slave device) R/W = 0 = write R/W = 1 = read A = 0 = Slave Device Acknowledges byte A = 1 = Slave Device does not Acknowledge byte “0” “1” “0” “1” “1” “1” “1” Device I2C Address Comment MCP4017 ‘0101111’ MCP4018 ‘0101111’ MCP4019 ‘0101111’ 0 00 0 S 000 0 X xxxx Ax x 0 A P General Call Address Second Byte “7-bit Command” Reserved 7-bit Commands (By I2C Specification - Philips # 9398 393 40011, Ver. 2.1 January 2000) ‘0000 011’b - Reset and write programmable part of slave address by hardware. ‘0000 010’b - Write programmable part of slave address by hardware. ‘0000 000’b - NOT Allowed The Following is a “Hardware General Call” Format 0 000 S 0000 X xx xx A xx1 A General Call Address Second Byte “7-bit Command” X xxxx xxX A P n occurrences of (Data + A / A) This indicates a “Hardware General Call” MCP4016/7/8/9 will ignore this byte and all following bytes (and A), until a Stop bit (P) is encountered. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |