M7020R datasheet(66/150 Pages) STMICROELECTRONICS

66 / 150 page

M7020R

66/150

136-bit Search on Tables Configured as x136 Using Up to Eight M7020R Devices

The hardware diagram of the search subsystem of

eight devices is shown in Figure 44, page 67. The

following are parameters programmed into the

eight devices:

– First seven devices (devices 0–6):

CFG = 01010101, TLSZ = 01, HLAT = 010,

LRAM = 0, and LDEV = 0.

– Eighth device (device 7):

CFG = 01010101, TLSZ = 01, HLAT = 010,

LRAM = 1, and LDEV = 1.

Note: All eight devices must be programmed with

the same value of TLSZ and HLAT. Only the last

device in the table must be programmed with

LRAM = 1 and LDEV = 1 (Device 7 in this case).

All other upstream devices must be programmed

with LRAM = 0 and LDEV = 0 (Devices 0 through

6 in this case).

Figure 46, page 69 shows the timing diagram for a

SEARCH command in the 136-bit-configured ta-

ble of eight devices for Device 0. Figure 47, page

70 shows the timing diagram for a SEARCH com-

mand in the 136-bit-configured table consisting of

eight devices for Device 1. Figure 48, page 71

shows the timing diagram for a SEARCH com-

mand in the 136-bit configured table consisting of

eight devices for Device 7 (the last device in this

specific table). For these timing diagrams, four

136-bit searches are performed sequentially, and

the following HIT/MISS assumptions were made

(see Table 35)

The following is the sequence of operation for a

single 136-bit SEARCH command (see COM-

MAND CODES AND PARAMETERS, page 29).

– Cycle A: The host ASIC drives CMDV high and

applies SEARCH command code ('10') on

CMD[1:0] signals. CMD[5:3] signals must be

driven with the index to the GMR pair for use in

this SEARCH operation. CMD[8:7] signals must

be driven with the same bits that will be driven

by this device on SADR[21:20] if it has a hit.

DQ[67:0] must be driven with the 68-bit data

([135:68]) in order to be compared against all

even locations. The CMD[2] signal must be driv-

en to a logic '0.'

– Cycle B: The host ASIC continues to drive

CMDV high and to apply the command code for

command

('10')

CMD[1:0].

CMD[5:2] must be driven by the index of the

comparand register pair for storing the 136-bit

word presented on the DQ Bus during Cycles A

and B. CMD[8:6] signals must be driven with the

SSR Index that will be used for storing the

address of the matching entry and the Hit

Flag (see

SEARCH-Successful

Registers

(SSR[0:7]), page 23). The DQ[67:0] is driven

with 68-bit data ([67:0]) compared against all

odd locations.

The logical 136-bit search operation is shown in

Figure 45, page 68. The entire table (eight devices

of 136-bit entries) is compared to a 136-bit word K

(presented on the DQ Bus in Cycles A and B of the

command) using the GMR and local mask bits.

The GMR is the 136-bit word specified by the even

and odd global mask pair selected by the GMR In-

dex in the command’s Cycle A.

The 136-bit word K (presented on the DQ Bus in

Cycles A and B of the command) is also stored in

the even and odd comparand registers specified

by the Comparand Register Index in the com-

mand’s Cycle B. In x136 configurations, the even

and odd comparand registers can subsequently

be used by the LEARN command in only one of

the devices (the first non-full device). The word K

(presented on the DQ Bus in Cycles A and B of the

command) is compared to each entry in the table

starting at location “0.” The first matching entry’s

location, “L,” is the winning address that is driven

as part of the SRAM address on the SADR[21:0]

lines (see SRAM ADDRESSING, page 126). The

global winning device will drive the bus in a specif-

ic cycle. On global miss cycles the device with

LRAM = 1 (the default driving device for the SRAM

Bus) and LDEV = 1 (the default driving device for

SSF and SSV signals) will be the default driver for

such missed cycles.

Note: During 136-bit searches of 136-bit-config-

ured tables, the search hit will always be at an

even address.

The SEARCH command is a pipelined operation

and executes a search at half the rate of the fre-

quency of CLK2X for 136-bit searches in x136-

configured tables. The latency of SADR, CE_L,

ALE_L, WE_L, SSV, and SSF from the 136-bit

SEARCH command cycle (two CLK2X cycles) is

shown in Table 36, page 72.

For one to eight devices in the table and

TLSZ = 01, the latency of a SEARCH from com-

mand to SRAM access cycle is 5. In addition, SSV

and SSF shift further to the right for different val-

ues of HLAT as specified in Table 37, page 72.

M7020R датащи(PDF) 66 Page - STMicroelectronics

M7020R датащи(HTML) 66 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL