LMP8350

www.ti.com

SNOSB80C – FEBRUARY 2011 – REVISED OCTOBER 2015

6.7 5-V Electrical Characteristics

Unless otherwise specified, all limits are ensured for TA = 25°C, Avcl = +1, RF= RG = 1 kΩ, Fully differential input, VS = +5 V,

RL = 2 kΩ//20 pF differentially, Input CMR and VOCM = mid-supply and HP mode unless otherwise noted.

(1)

PARAMETER

TEST CONDITIONS

MIN(2)

TYP(3)

MAX(2)

UNIT

5-V DC CHARACTERISTICS

TA = 25°C

±0.2

±3.2

High power

At the temperature extremes

±3.6

TA = 25°C

±0.1

±2.0

Input offset voltage

VOS

Mid power

mV

(RTI)

At the temperature extremes

±2.3

TA = 25°C

±0.1

±2.0

Low power

At the temperature extremes

±2.3

High power

±0.7

TCVO

Input offset voltage

Mid power

±0.5

μV/°C

S

vs.temperature(4)

Low power

±0.4

TA = 25°C

1.5

High power

At the temperature extremes

1.6

TA = 25°C

2.5

IB

Input bias current

Mid power

μA

At the temperature extremes

3.0

TA = 25°C

3.5

Low power

At the temperature extremes

3.7

High power

63

68

AVOL

Open-loop gain

Mid power

71

75

dB

Low power

68

75

HP at CMRR

≥ 60 dB

1.15

3.85

CMVR Common-mode voltage range(5)

MP at CMRR

≥ 86 dB

1.15

3.85

V

LP at CMRR

≥ 80 dB

1.15

3.85

DC, VOCM = 0,VID = 0,

ΔVcm = ±0.2 V

63

79

High power

CMRR Common-mode rejection ratio

dB

Mid power

87

114

Low power

82

114

ZIND

Differential input resistance

VCM = mid-supply

0.48

M

Ω

CIND

Differential input capacitance

VCM = mid-supply

1

pF

Low Swing

0.82

0.77

4.18

High power

High Swing

0.82

4.23

4.18

Low Swing

0.82

0.75

4.18

Output swing

VO

Mid power

V

(single-ended)

High Swing

0.82

4.25

4.18

Low Swing

0.83

0.77

4.17

Low power

High Swing

0.83

4.23

4.17

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA

(2)

Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using the

Statistical Quality Control (SQC) method.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(4)

Drift Determined by dividing the change in parameter at temperature extremes by the total temperature change. Value is the worst case

of TaMIN to 25°C and 25°C to TaMAX.

(5)

At amplifier inputs.

Copyright © 2011–2015, Texas Instruments Incorporated

Submit Documentation Feedback

11

Product Folder Links: LMP8350