LMP8350

www.ti.com

SNOSB80C – FEBRUARY 2011 – REVISED OCTOBER 2015

6.5 10-V Electrical Characteristics

Unless otherwise specified, all limits are ensured for TA = 25°C, Avcl = +1, RF = RG = 1 kΩ, Fully differential input, VS = +10

V, RL = 2 kΩ//20 pF differentially, Input CMR and VOCM = mid-supply and HP mode unless otherwise noted.

(1)

PARAMETER

TEST CONDITIONS(2)

MIN(3)

TYP(4)

MAX(3)

UNIT

10-V DC CHARACTERISTICS

TA = 25°C

±0.6

±4

High power

At the temperature extremes

±4.05

TA = 25°C

±0.08

±2

Input offset voltage

VOS

Mid power

mV

(RTI)

At the temperature extremes

±2.03

TA = 25°C

±0.1

±2.5

Low power

At the temperature extremes

±2.52

High power

±0.8

TCVOS

Input offset voltage vs.temperature(5) Mid power

±0.5

μV/°C

Low power

±0.4

TA = 25°C

2

High power

At the temperature extremes

2.1

TA = 25°C

2.7

IB

Input bias current

Mid power

μA

At the temperature extremes

3.2

TA = 25°C

3.5

Low power

At the temperature extremes

3.7

High power

65

90

AVOL

Open-loop gain

Mid power

72

130

dB

Low power

74

114

HP at CMRR

≥ 73 dB

1.2

8.8

CMVR

Common-mode voltage range(6)

MP at CMRR

≥ 83 dB

1.2

8.8

V

LP at CMRR

≥ 77 dB

1.2

8.8

DC, VOCM = 0,VID = 0, ΔVcm = ±0.2 V, High power

75

90

CMRR

Common-mode rejection ratio

Medium power

84

130

dB

Low power

79

114

ZIND

Differential input resistance

VCM = mid-supply

0.48

M

Ω

CIND

Differential input capacitance

VCM = mid-supply

1

pF

Low Swing

0.86

0.75

9.14

High power

High Swing

0.86

9.25

9.14

Low Swing

0.85

0.74

9.15

Output swing

VO

Mid power

V

(single-ended)

High Swing

0.85

9.26

9.15

Low Swing

0.86

0.81

9.14

Low power

High Swing

0.86

9.19

9.14

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA

(2)

For annotation brevity, “HP”=High Power, “MP”=Medium Power, “LP” =Low Power, “DIS”=Disabled or shut down, “SE”=Single Ended

Mode, “DM”=Differential Mode. See Table 1 in Applications section for power setting details. It is also assumed RG = RG1 = RG2

(3)

Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using the

Statistical Quality Control (SQC) method.

(4)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(5)

Drift Determined by dividing the change in parameter at temperature extremes by the total temperature change. Value is the worst case

of TaMIN to 25°C and 25°C to TaMAX.

(6)

At amplifier inputs.

Copyright © 2011–2015, Texas Instruments Incorporated

Submit Documentation Feedback

5

Product Folder Links: LMP8350