BMP585 datasheet(24/71 Pages) BOSCH

24 / 71 page

Bosch Sensortec

| BST-BMP585-DS003-02

24 | 71

Document number: BST-BMP585-DS003-02

as well as in the event of applications for industrial property rights

The two modes differ in how the FIFO reacts to an overflow. A FIFO overflow occurs if the FIFO is full and a new

measurement data is ready to be written to the FIFO. In streaming mode, the FIFO will delete the oldest frame, and write

the new frame to the FIFO. As a result, the FIFO contains always the most recent frames.2

In stop-on-full mode, frames once written to the FIFO will not be discarded. Instead, new frames will not be written to the

FIFO until there is space again.

The FIFO decimation factor (or downsampling) can be adjusted With FIFO_SEL.cfg_fifo_dec_sel. Only every n-th

sample will be written to the FIFO, where:

��=2��_SEL.cfg_fifo_dec_sel

The FIFO threshold can be set by FIFO_CONFIG_fifo_threshold. If the fill level of the FIFO reaches the threshold, the

FIFO threshold interrupt may be triggered (see section 4.7.2.1). The meaning of the register field is the following:



0x00: FIFO threshold disabled



0x01..0x1F (or 1..31 decimal): threshold level



0x0F: 15 frames. This is the maximum setting in PT-mode. The most significant bit is ignored.



0x1F: 31 frames. This is the maximum setting in P- or T-mode.

4.6.2 FIFO status

The fill level of the FIFO in number of frames can be obtained from FIFO_COUNT.fifo_count. FIFO watermark and FIFO

full information can be obtained from the interrupt functionality (see section 4.7.2.1).

4.6.3 FIFO data readout

The FIFO can be read out by reading in a burst from register FIFO_DATA.

Reads should be performed in the granularity of the frame size (24 or 48 bit) according to the selected frame type.

Frames that have been read incompletely will stay in the FIFO memory and will be retransmitted on the next read. The

entire FIFO contents can be read in one single burst.

If the FIFO is empty, disabled or turns empty during a read, it will return the empty frame, which is 0x7f.

Table 11, Table 12 and

Table 13 show the frame formats for the three different frame kinds: PT, T and P. The empty frame is shown in Table 14.

Table 11: FIFO pressure and temperature frame (PT-frame)

Table 12: FIFO temperature frame (T-frame)

2 In order to work properly, streaming mode requires that the clock frequency of host interface is 0.1 MHz or above. Otherwise, the FIFO

readout bandwidth could be slower than the FIFO write bandwidth, which will cause data loss.

Temperature

temperature XLSB

temperature LSB

temperature MSB

Pressure

pressure XLSB

press LSB

press MSB

Temperature

temperature XLSB

temperature LSB

temperature MSB

BMP585 датащи(PDF) 24 Page - Bosch Sensortec GmbH

BMP585 датащи(HTML) 24 Page - Bosch Sensortec GmbH

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

датащи скачать

ссылки URL