SLE datasheet(53/93 Pages) WINCHESTER

53 / 93 page

Omit steps not required

S-2

XMRE 34

S-2

XMRA 34

-F

110

Guides

G- Cylindrical guide with single spring member.

Recommended for ground only.

K- Cylindrical guide with four spring members.

May be used for electrical contact.

N- Cylindrical guide without spring member.

Recommended for extra mechanical strength.

Jackscrews and Jacksockets

***

M- Polarized short turnable jackscrew and

jacksocket. Cannot be used with hoods.

***

C- Polarized long turnable jackscrew and

jacksocket for use with hoods.

***D- Polarized turnable jackscrew and jacksocket

for use with hoods for sizes 34 thru 104

excluding 41.

*** F- Polarized fixed jackscrew and jacksocket.

***

J-

Non-polarized short turnable jackscrews.

Cannot be used with hoods.

***L- Non-polarized long turnable jackscrews.

***R- Non-polarized fixed jacksocket.

***

FZ- Same as F but with 6-32 mtg thd (std on 104).

***

MW-Same as M but with knurled round knob with

internal hex (not avail. 104).

***MU- Same as M but with knurled round knob with

screwdriver slot (not avail. 104).

***MX- Same as M but with hex knob (not avail 104).

***CW- Same as C but with knurled round knob with

internal hex (not avail. 104).

***

CU- Same as C but with knurled round knob with

screwdriver slot (not avail. 104).

***

CX- Same as C but with hex knob (not avail. 104).

***

CZ- Same as C but with prybar knob

(not avail. 104).

*** Request availablity information.

***

Material: Nickel-plated brass - standard

Potting Form or Hoods:

0- When no potting form or hood is required.

1- Potting form style #0100. Cannot be used with hood.

Request availability information.

Cannot be used

Formed Hoods:

3- Hood, top opening, style #0300, for use with Type “C”

or “D” jackscrews.

4- Hood, side opening, style #0400, for use with Type “C”

or “D” jackscrews.

5- Hood, top opening, style #0500, for use with “G”, “K”,

or “N” type guides only and “F” style jackscrews.

6- Hood, side opening, style #0600, for use with “G”, “K”,

or “N” type guides only and “F” style jackscrews.

Deep Drawn Hoods:

7- Hood, top opening, style #0700, for use with Type “C”

or “D” jackscrews.

8- Hood, side opening, style #0800, for use with Type “C”

or “D” jackscrews.

9- Hood, top opening, style #0900, for use with “G”, “K”,

and “N” type guides or “F” jackscrews.

2- Hood, side opening, style #0200, for use with “G”, “K”,

or “N” type guides or “F” jackscrews.

Note: Addition of “X” to end of code # indicates cable

opening larger than std. See hoods for cable opening

size.

Example: XMRE34PD3A300X

■

Step 2

Pin or

Socket

Contacts:

P - Pin

S - Socket

■

Step 3

Type of

Contact:

Blank =

Standard

Solder Cup

Straight

Dip Solder

.030" dia.=

XMRA

.025" dia.=

XMRE

D3 = .094"

D4 = .125"

D5 = .156"

For additional

lengths in 1/32"

increments,

contact

Winchester’s

Sales

Department.

■

Step 4

■

Step 4

Guides

Jackscrews

and

Jacksockets

(See bottom

chart)

■

Step 6

Polarization

Position:

A, B, C, D, E,

F or G.

Omit letter

when

polarization is

not required.

■

Step 7

(See

bottom

chart)

■

Step 7

■

Step 9

Special Gaskets:

Omit letter when gaskets

are not required.

G- Bulkhead gasket, style

#0000G. Use only

when mounting plate is

specified.

F- Face gasket, style

#0000F. Use with

male insert only.

B- If both gasket #0000G

and gasket #0000F

are desired.

Check plant for availability

on all gaskets.

■

Step 8

Mounting Plate

or Finger Grips:

00- When no

mounting

plate is

required

*10- Mounting

plate, style

#0010.

*Mounting plates

are not used with

“M”, “C”, “D”, “J”,

or “L” jackscrews.

■

Step 5

Shell Type:

0 No shell.

1 Plug shell, style

1*000.

2 Receptacle shell,

style 2*000.

3 Plug shell,

monojack type,

style 3*000.

4 Receptacle,

monojack type,

style 4*000.

** 7 Stainless Steel

Plug shell, style

7*000 (66 & 104

only)

** 8 Stainless Steel

Receptacle shell,

style 8*000 (66 &

104 only)

* Polarizing Position

** Request availablity

information.

■

Step 1

Insert Code

No. of

Contacts:

XMRA 9,

14, 20, 34,

42, 50, 50-8,

66, 75, 104

XMRE 9,

14, 18, 20,

26, 34, 42,

50, 75, 104

By adding “ML”

to the series

code, connector

is supplied with

diallyl phthalate

type SDG-F

and mil plated

contacts.

Example:

XMREML

XMRAML

XMRA & XMRE Series

RP /

www.winconn.com

Ordering Information

SLE датащи(PDF) 53 Page - Winchester Electronics Corporation

SLE датащи(HTML) 53 Page - Winchester Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL