SLE datasheet(20/93 Pages) WINCHESTER

20 / 93 page

XAC

Omit steps not required

■

Step 9

Special Gaskets:

Omit letter when gaskets

are not required.

G- Bulkhead gasket, style

#0000G. Use only

when mounting plate is

specified.

F- Face gasket, style

#0000F. Use with

male insert only.

B- If both gasket #0000G

and gasket #0000F

are desired.

Check plant for availability

on all gaskets.

■

Step 8

Mounting Plate:

00- When no

mounting

plate is

required

*10- Mounting

plate, style

#0010.

Note: See section

XMRA/E RP/

57.

*Mounting plates

are not used with

“M”, “C” or “D”

jackscrews.

■

Step 7

(See

bottom

chart)

■

Step 6

Polarization

Position:

A, B, C, D,

E, F or G.

Omit letter

when

polarization

is not

required.

■

Step 5

Shell Type:

0 No shell

1 Plug shell,

style 1*000.

2 Receptacle

shell, style

2*000.

3 Plug shell,

monojack

type,

style 3*000.

4 Receptacle,

monojack type,

style 4*000.

7 Stainless Steel

Plug shell, style

7*000.

8 Stainless Steel

Receptacle shell,

style 8*000.

Polarizing Position

Request availability

information

■

Step 4

Jackscrews

(See

bottom

chart)

■

Step 3

Pin or

Socket

Contacts:

P - Pin

S - Socket

■

Step 1

Series:

XAC, XNAC

Numerical

contact

identification

on sizes 34,

50, and 104.

■

Step 2

No. of

Contacts:

9, 14, 18, 20,

26, 34, 42,

50, 66, 75,

and 104

See note 1

below

Guides

G-

Cylindrical guide with single spring member.

Recommended for ground only.

K-

Cylindrical guide with four spring members.

May be used for electrical contact.

N-

Cylindrical guide without spring member.

Recommended for extra mechanical strength.

Jackscrews and Jacksockets

*** M- Polarized short turnable jackscrew and

jacksocket. Cannot be used with hoods.

***

C- Polarized long turnable jackscrew and

jacksocket for use with hoods.

***

D- Polarized one-piece mono-jackscrew and

mono-jacksocket (no separate knob); to be

used with hoods on sizes: 34, 42, 50, 66, 75,

and 104.

***

F- Polarized fixed jackscrew and jacksocket

usable with or without hood; (no knob

required).

** MW- Same as M but with knurled round knob with

internal hex.

** MU- Same as M but with knurled round knob with

screwdriver slot.

MX- Same as M but with hex knob.

CW- Same as C but with knurled round knob with

internal hex.

CU- Same as C but with knurled round knob with

screwdriver slot.

** CX- Same as C but with hex knob.

** CZ- Same as C but with prybar knob.

Request availability information

*** Material: Nickel Plated Brass standard

■

Step 4

■

Step 7

Formed Hoods:

0- No Hood.

3- Hood, top opening, style #0300, for use with Type “C”

or “D” jackscrews.

4- Hood, side opening, style #0400, for use with Type “C”

or “D” jackscrews.

5- Hood, top opening, style #0500J, for use with “F”

style jackscrews.

6- Hood, side opening, style #0600J, for use with “F”

style jackscrews.

Deep Drawn Hoods:

7- Hood, top opening, style #0700, for use with Type “C”

or “D” jackscrews.

8- Hood, side opening, style #0800, for use with Type “C”

or “D” jackscrews.

9- Hood, top opening, style #0900, for use with

“F” jackscrews.

2- Hood, side opening, style #0200, for use with

“F” jackscrews.

Note: Addition of “X” to code # indicates cable opening

larger than std. See hoods for cable opening size.

Example: XAC20PC1A300 X

Note: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel

External Miniature Rectangular, Removable Contacts

XAC Series

Ordering Informations

RP /

SLE датащи(PDF) 20 Page - Winchester Electronics Corporation

SLE датащи(HTML) 20 Page - Winchester Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL