SLE datasheet(33/93 Pages) WINCHESTER

33 / 93 page

Omit steps not required

■

Step 1

Insert Series

Code

By adding “ML”

to the series

code, connector

is supplied with

diallyl phthalate

type SDG-F

and mil plated

contacts.

Example:

MRAML

■

Step 3

Contact

Designation:

P - Pin

S - Socket

When

ordering

molding less

hardware to

be used with

mono-jacks,

see Note

below.

■

Step 4

Type of

Contact:

Blank =

Standard

Solder Cup

Straight

Dip Solder

.030" dia.:

D3 = .094"

D4 = .125"

D5 = .156"

For additional

lengths in 1/32"

increments,

contact

Winchester’s

Sales

Department.

■

Step 5

Guides and

Jackscrew

Locks:

(See bottom

Chart)

■

Step 6

Hoods:

H - Standard

Top

Opening*

H1 - Standard

Side

Opening

H8 - Large Top

Opening

H9 - Large Side

Opening

See Hood

Section for

Availability

*(Note: H Hoods

for MRA 9, 14

and 20 will not

accept JTC

hardware. Use

H8 hoods.)

■

Step 7

Vibration

Locks:

V - Lock Tab

V2 - Lock Tab

(Size 50

& 75)

VL - Lever &

Pivot Ass’y

VL2 - Lever &

Pivot Ass’y

(Size 50

& 75)

■

Step 8

Accessories:

FM - Potting

Forms.

Cannot be

Used with

Hoods.

Request

availability

informa-

tion.

■

Step 9

Special

Options:

Consult Sales

Department

Guides

Phosphor Bronze Cylindrical Guides*

Beryllium Copper Cylindrical Guides

Brass Cylindrical Guides*

Guides are not recommended for Size 104

“P” indicates two guide pins or two jackscrews

(EX. JTCP)

“S” indicates two guide sockets or two jacksockets.

(Ex. GS)

Jackscrew Locks

*** J

Polarized Fixed Jackscrew and Jacksocket

Polarized Short Turning Jackscrew

and Jacksocket

JTC

Polarized Long Turning Jackscrew

and Jacksocket

JTD

Polarized Long Turning Mono-Jackscrew and

Mono-Jacksocket for Sizes 34, 42, 50, 66,

75, and 104 only.

■

Step 5

* For passivated stainless steel add SS suffix. (

Example: MRA34SGSS)

Mounting Note: Connectors MRA 9, MRA 14, MRA 20 and MRA41 use guides or fixed jacks for mounting in a

hood or on a panel. Connectors MRA 34, MRA 42, MRA 50, MRA 66, MRA 75 use four #4 machine screws,

and MRA 104 uses four #6 machine screws for mounting in a hood or on a panel. Guides are not recom-

mended for use with MRA 104.

MRA

GVL

Note: When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connec-

tors must be ordered as follows:

Pin connector = MRA34P8, MRA42P8, etc.

Socket connector = MRA34S8, MRA42S8, etc.

The number “8” indicates special housing for use with the JTD Monojack hardware

(available on sizes 34, 42, 50, 66, 75 and 104).

**JZ

Same as J but with 6-32 mtg. thd.

(Std. on 104)

**JTW Same as JT but with knurled round knob

with internal hex (not avail. 104)

**JTU Same as JT but with knurled round knob

with screwdriver slot (not avail. 104)

**JTX Same as JT but with hex knob

(not avail. 104)

**JTCW Same as JTC but with knurled round knob

with internal hex (not avail. 104)

**JTCU Same as JTC but with knurled round knob

with screwdriver slot (not avail. 104)

**JTCX Same as JTC but with hex knob

(not avail. 104)

**JTCZ Same as JTC but with prybar knob

(not avail. 104)

** Request availablity information.

***Material: Nickel-plated brass - standard.

■

Step 2

Number of

Contacts:

9, 14, 20, 34,

41, 42, 50,

50-8, 66, 75,

104

***

MRA Series

RP /

www.winconn.com

Ordering Information

SLE датащи(PDF) 33 Page - Winchester Electronics Corporation

SLE датащи(HTML) 33 Page - Winchester Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL