SLE datasheet(43/93 Pages) WINCHESTER

43 / 93 page

Omit steps not required

■

Step 4

Type of

Contact:

Blank =

Standard

Solder Cup

Straight

Dip Solder

.025" dia.:

D3 = .094"

D4 = .125"

D5 = .156"

For additional

lengths in 1/32"

increments,

contact

Winchester’s

Sales

Department.

■

Step 5

Guides and

Jackscrew

Locks:

(See bottom

Chart)

■

Step 6

Hoods:

H - Standard

Top

Opening*

H1 - Standard

Side

Opening

H8 - Large Top

Opening

H9 - Large Side

Opening

*For MRE 7, 8,

9, 14, 18 and 20,

JTC hardware

may not be used

with H hoods.

Use H8 hoods.

■

Step 7

Vibration

Locks:

V - Lock Tab

V2 - Lock Tab

(Size 50

& 75)

VL - Lever & Pivot

Ass’y

VL2 - Lever & Pivot

Ass’y (Size

50 & 75)

■

Step 8

Accessories:

FM - Potting

Forms.

Cannot be

Used with

Hoods.

Request

availability

informa-

tion.

■

Step 9

Special

Options:

Consult Sales

Department

Guides

Phosphor Bronze Cylindrical Guides*

Beryllium Copper Cylindrical Guides

Brass Cylindrical Guides*

Guides are not recommended for Size 104

“P” indicates two guide pins or two jackscrews

(Ex. JTCP)

“S” indicates two guide sockets or two jacksockets.

(Ex. GS)

Jackscrew Locks

***J

Polarized Fixed Jackscrew and Jacksocket

Polarized Short Turning Jackscrew

and Jacksocket

JTC

Polarized Long Turning Jackscrew

and Jacksocket

JTD

Polarized Long Turning Mono-Jackscrew and

Mono-Jacksocket for Sizes 34, 42, 50, 75,

and 104 only.

■

Step 5

MRE

GVL

* For passivated stainless steel add SS suffix (Example: MRE34SGSS)

Mounting Note: Connectors MRE 41, MRE 26, and smaller use guides for mounting in a hood or on a panel.

Connectors MRE 34, MRE 42, MRE 50, MRE 75, use four #4 machine screws, in addition to guides, for

mounting in a hood or on a panel.

**JZ

Same as J but with 6-32 mtg. thd. (Not

available 5-3, 8) (Std. on 104)

**JTW Same as JT but with knurled round knob

with internal hex (not avail. 5-3, 8, 104)

**JTU Same as JT but with knurled round knob

with screwdriver slot (not avail. 5-3, 8, 104)

**JTX Same as JT but with hex knob (not avail. 5-

3, 8, 104)

**JTCW Same as JTC but with knurled round knob

with internal hex (not avail. 5-3, 8, 104)

**JTCU Same as JTC but with knurled round knob

with screwdriver slot (not avail. 5-3, 8, 104)

**JTCX Same as JTC but with hex knob (not avail.

5-3, 8, 104)

**JTCZ Same as JTC but with prybar knob.

** Request availablity information.

***Material: Nickel-plated brass - standard

Example: MRE34SJTDBH8

Note: When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connec-

tors must be ordered as follows:

Pin connector = MRE34P8, MRE42P8, etc.

Socket connector = MRE34S8, MRE42S8, etc.

The number “8” indicates special housing for use with the JTD Monojack hardware

(available on sizes 34, 42, 50, 66, 75 and 104).

■

Step 1

Insert Series

Code:

MRE

By adding “ML”

to the series

code, connector

is supplied with

diallyl phthalate

type SDG-F

and mil plated

contacts.

Example: MREML

■

Step 3

Contact

Designation:

P - Pin

S - Socket

When

ordering

molding less

hardware to

be used with

mono-jacks,

see note

below.

■

Step 2

Number of

Contacts:

7, 8, 9, 11,

14, 18, 20,

21, 26, 34,

41, 42, 50,

75, 104

***

MRE Series

RP /

www.winconn.com

Ordering Information

SLE датащи(PDF) 43 Page - Winchester Electronics Corporation

SLE датащи(HTML) 43 Page - Winchester Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL