SLE datasheet(22/93 Pages) WINCHESTER

22 / 93 page

Omit steps not required

■

Step 4

Guides and

Jackscrew

Locks:

(See bottom

Chart)

■

Step 5

Hoods:

H - Standard top opening.

Sizes 26, 34, 42 &

50 only.

H1 - Standard side opening.

Available all sizes.

H8 - Large top opening.

Sizes 26, 34, 42 &

50 only.

H9 - Large side opening.

Available all sizes.

H13 -Large top opening,

high hood. Sizes 9, 14,

18 & 20 only.

GVL

■

Step 6

Vibration

Locks:

V - Lock Tab

V2 - Lock Tab

(Size 50)

VL - Lever &

Pivot Ass’y

VL2- Lever &

Pivot Ass’y

(Size 50)

■

Step 7

Special

Options:

Consult Sales

Department

■

Step 1

Insert Series

Code:

TMRAC

■

Step 2

Number of

Contacts:

9, 14, 18,

20, 26, 34,

42, 50,

See note 1

below.

■

Step 3

Contact

Designation:

P - Pin

S - Socket

When

ordering

moldings less

hardware for

use with

mono-jacks,

see note 2

below.

TMRAC

Guides

Phosphor Bronze Cylindrical Guides

Beryllium Copper Cylindrical Guides

Brass Cylindrical Guides

“P” indicates two guide pins or two jackscrews

(EX. JTCP)

“S” indicates two guide sockets or two jacksockets

(Ex. GS)

* For passivated stainless steel add SS suffix.

Jackscrew Locks

***J

Polarized Fixed Jackscrew and Jacksocket

Polarized Short Turning Jackscrew and

Jacksocket

JTC

Polarized Long Turning Jackscrew and

Jacksocket

JTD

Polarized Long Turning Mono-Jackscrew and

Mono-Jacksocket for Sizes 34, 42, and

50 only.

**JZ

Same as J but with 6-32 mtg. thd.

**JTW Same as JT but with knurled round knob

with internal hex

**JTU Same as JT but with knurled round knob

with screwdriver slot

**JTX Same as JT but with hex knob

**JTCW Same as JTC but with knurled round knob

with internal hex

**JTCU Same as JTC but with knurled round knob

with screwdriver slot

**JTCX Same as JTC but with hex knob

**JTCZ Same as JTC but with prybar knob

** Request availablity information.

***Material: Nickel Plated Brass standard

■

Step 4

Notes: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel

2. When ordering hoods, hardware and connectors separately for use with JTD Monojacks,

connectors must be ordered as follows:

Pin connector = TMRAC34P8, TMRAC42P8, etc.

Socket connector = TMRAC34S8, TMRAC42S8, etc.

The number “8” indicates special housing for use with the JTD Monojack hardware

(available on sizes 34, 42, and 50).

All dimensions for TMRAC housings are the

same as MRAC housings. All hoods, hardware,

and accesories used on the TMRAC Series are

the same as those used on the MRAC Series.

See MRAC Series section for part numbers and

dimensions. Note the TMRAC Series maximum

number of contacts is 50.

***

TMRAC Series

Ordering Information

Dimensions

RP /

SLE датащи(PDF) 22 Page - Winchester Electronics Corporation

SLE датащи(HTML) 22 Page - Winchester Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL