DSP56366 datasheet(34/110 Pages) FREESCALE

34 / 110 page

DSP56366 Technical Data, Rev. 3.1

3-8

Freescale Semiconductor

Interrupt Requests Rate

• HDI08, ESAI, ESAI_1, SHI, DAX, Timer

•DMA

•IRQ, NMI (edge trigger)

•IRQ (level trigger)

12TC

8TC

12TC

—

100.0

66.7

100.0

DMA Requests Rate

• Data read from HDI08, ESAI, ESAI_1, SHI, DAX

• Data write to HDI08, ESAI, ESAI_1, SHI, DAX

•Timer

•IRQ, NMI (edge trigger)

6TC

7TC

2TC

3TC

—

50.0

58.0

16.7

25.0

Delay from IRQA, IRQB, IRQC, IRQD, NMI assertion to

external memory (DMA source) access address out valid

4.25

× T

C + 2.0

37.4

—

1 V

CC = 3.3 V ± 0.16 V; TJ = –40°C to + 110°C, CL = 50 pF

2 Periodically sampled and not 100% tested.

3 RESET duration is measured during the time in which RESET is asserted, V

CC is valid, and the EXTAL input is active and

valid. When the VCC is valid, but the other “required RESET duration” conditions (as specified above) have not been yet met,

the device circuitry will be in an uninitialized state that can result in significant power consumption and heat-up. Designs

should minimize this state to the shortest possible duration.

4 If PLL does not lose lock.

5 When using fast interrupts and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through 21 apply to

prevent multiple interrupt service. To avoid these timing restrictions, the deasserted Edge-triggered mode is recommended

when using fast interrupts. Long interrupts are recommended when using Level-sensitive mode.

6 WS = number of wait states (measured in clock cycles, number of T

C). Use expression to compute maximum value.

7 This timing depends on several settings:

For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time will be defined

by the PCTL Bit 17 and OMR Bit 6 settings.

For PLL enable, if PCTL Bit 17 is 0, the PLL is shutdown during Stop. Recovering from Stop requires the PLL to get locked.

The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range of 0 to 1000 cycles. This procedure occurs in

parallel with the stop delay counter, and stop recovery will end when the last of these two events occurs: the stop delay

counter completes count or PLL lock procedure completion.

PLC value for PLL disable is 0.

The maximum value for ETC is 4096 (maximum MF) divided by the desired internal frequency (i.e., for 120 MHz it is 4096/120

MHz = 34.1

μs). During the stabilization period, T

C, TH, and TL will not be constant, and their width may vary, so timing may

vary as well.

Table 3-7 Reset, Stop, Mode Select, and Interrupt Timing1 (continued)

No.

Characteristics

Expression

Min

Max

Unit

DSP56366 датащи(PDF) 34 Page - Freescale Semiconductor, Inc

DSP56366 датащи(HTML) 34 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL