ST10F276 datasheet(176/229 Pages) STMICROELECTRONICS

176 / 229 page

Electrical characteristics

ST10F276

176/229

Electrical characteristics

23.1

Absolute maximum ratings

Note:

Stresses above those listed under “Absolute Maximum Ratings” may cause permanent

damage to the device. This is a stress rating only and functional operation of the device at

these or any other conditions above those indicated in the operational sections of this

specification is not implied. Exposure to absolute maximum rating conditions for extended

periods may affect device reliability. During overload conditions (VIN > VDD or VIN < VSS) the

voltage on pins with respect to ground (VSS) must not exceed the values defined by the

Absolute Maximum Ratings.

During Power-on and Power-off transients (including Stand-by entering/exiting phases), the

relationships between voltages applied to the device and the main VDD must always be

respected. In particular, power-on and power-off of VAREF must be coherent with the VDD

transient, in order to avoid undesired current injection through the on-chip protection diodes.

23.2

Recommended operating conditions

Table 86.

Absolute maximum ratings

Symbol

Parameter

Value

Unit

VDD

Voltage on VDD pins with respect to ground (VSS)

- 0.3 to +6.5

VSTBY

Voltage on VSTBY pin with respect to ground (VSS)

VAREF

Voltage on VAREF pin with respect to ground (VSS)

- 0.3 to VDD + 0.3

VAGND

Voltage on VAGND pin with respect to ground (VSS)VSS

VIO

Voltage on any pin with respect to ground (VSS)

- 0.5 to VDD + 0.5

IOV

Input current on any pin during overload condition

± 10

ITOV

Absolute sum of all input currents during overload condition

| 75 |

TST

Storage temperature

- 65 to +150

°C

ESD

ESD susceptibility (human body model)

2000

Table 87.

Recommended operating conditions

Symbol

Parameter

Min.

Max.

Unit

VDD

Operating supply voltage

4.5

5.5

VSTBY

Operating stand-by supply voltage(1)

The value of the VSTBY voltage is specified in the range 4.5 - 5.5 volts. Nevertheless, it is acceptable to

exceed the upper limit (up to 6.0 volts) for a maximum of 100 hours over the global 300000 hours,

representing the lifetime of the device (about 30 years). On the other hand, it is possible to exceed the

lower limit (down to 4.0 volts) whenever RTC and 32 kHz on-chip oscillator amplifier are turned off (only

Stand-by RAM powered through VSTBY pin in Stand-by mode). When VSTBY voltage is lower than main

VDD, the input section of VSTBY/EA pin can generate a spurious static consumption on VDD power supply

(in the range of tenth of

µA).

VAREF

Operating analog reference voltage(2)

VDD

Ambient temperature under bias

–40

+125

°C

Junction temperature under bias

+150

ST10F276 датащи(PDF) 176 Page - STMicroelectronics

ST10F276 датащи(HTML) 176 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL