| поискавой системы для электроныых деталей |
|
ST10F276 датащи(PDF) 174 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST10F276 датащи(HTML) 174 Page - STMicroelectronics |
|
174 / 229 page ![]() Register set ST10F276 174/229 The default XPER selection after Reset is such that CAN1 is enabled, CAN2 is disabled, XRAM1 (2 Kbyte XRAM) is enabled and XRAM2 (64 Kbyte XRAM) is disabled; all the other X-Peripherals are disabled after Reset. Register XPERCON cannot be changed after the global enabling of X-Peripherals, that is, after setting of bit XPEN in SYSCON register. In Emulation mode, all the X-Peripherals are enabled (XPERCON bits are all set). The bondout chip determines whether or not to redirect an access to external memory or to XBUS. Reserved bits of XPERCON register are always written to ‘0’. Table 85 below summarizes the Segment 8 mapping that depends upon the EA pin status during reset as well as the SYSCON (bit XPEN) and XPERCON (bits XRAM2EN and XFLASHEN) registers user programmed values. . Note: The symbol “x” in the table above stands for “do not care”. 22.10.1 XPERCON and XPEREMU registers As already mentioned, the XPERCON register must be programmed to enable the single XBUS modules separately. The XPERCON is a read/write ESFR register; the XPEREMU register is a write-only register mapped on XBUS memory space (address EB7Eh). Once the XPEN bit of SYSCON register is set and at least one of the X-peripherals (except memories) is activated, the register XPEREMU must be written with the same content of XPERCON: This is mandatory in order to allow a correct emulation of the new set of features introduced on XBUS for the new ST10 generation. The following instructions must be added inside the initialization routine: if (SYSCON.XPEN && (XPERCON & 0x07D3)) then { XPEREMU = XPERCON } Of course, XPEREMU must be programmed after XPERCON and after SYSCON; in this way the final configuration for X-Peripherals is stored in XPEREMU and used for the emulation hardware setup. Note: The bit meaning is exactly the same as in XPERCON. Table 85. Segment 8 address range mapping EA XPEN XRAM2EN XFLASHEN Segment 8 0 0 x x External memory 0100 External memory 0 1 1 x Reserved 01 x 1 Reserved 1 x x x IFlash (B1F1) XPEREMU (EB7Eh) XBUS Reset value xxxxh: 15 14 13 12 11 10 987 65432 10 --- -- XMISC EN XI2C EN XSSC EN XASC EN XPWM EN XFLAS HEN XRTC EN XRAM2 EN XRAM1 EN CAN2 EN CAN1 EN - - - - - RW RW RW RW RW RW RW RW RW RW RW |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |