AD5560JSVUZ datasheet(48/67 Pages) AD

48 / 67 page

Data Sheet

AD5560

Rev. E | Page 47 of 66

CONTROL REGISTERS

DPS AND DAC ADDRESSING

The serial word assignment consists of 24 bits, as shown in

Table 16. All write-to registers can be read back. There are

some read-only registers (Address 0x43 and Address 0x44).

DAC x2 registers are not available for readback.

A no operation (NOP) command performs no function within

the device. This code may be useful when performing a

readback function where a change of DAC or DPS register is

not required.

Table 16. Serial Word Assignment

B23

[B22:B16]

[B15:B0]

R/W

Address bits

Data bits

Table 17. Read or Write Register Addressing

Address

Default

Data Bits, MSB First

0x0

NOP

0x0000

NOP command; performs no operation.

0x1

System

control

0x0000

Bit

Name

Function

TMP[1:0]

Thermal shutdown bits. TMP1, TMP0 allow the user to program the thermal

shutdown temperature of operation.

TMP

Action

Shutdown at a T

J of 130°C (power-on default)

Shutdown at a T

J of 120°C

Shutdown at a T

J of 110°C

Shutdown at a T

J of 100°C

Gain[1:0]

MEASOUT output range. The MEASOUT range defaults to the voltage force span for

voltage and current measurements (this is ±12.81 V), which includes some overrange

to allow for error correction. The MEASOUT range can be reduced by using the gain

bits. This allows for use of asymmetrical supplies or for use of a smaller input range ADC.

MEASOUT gain settings do not translate the low voltage temperature sensor signal

(TSENSE).

Gain

MEASOUT Gain

MI Gain

0.2

To allow for system error correction, there is an additional gain of 0.125 for the force

function if this error correction is used as intended; then the output range on

MEASOUT scales accordingly (see Table 9).

FINGND

Writing a 1 to FINGND switches the positive input of the force amplifier to GND; when

0, the input of the force amplifier is connected to the output of the force DAC.

CPO

Write a 1 to the CPO bit to enable a simple window comparator function. In this

mode, only one comparator output is available (CPOH/CPO). This provides two bits of

information. The compared value is either inside or outside the window and enables

the user to bring only one line back to the controller per DPS device.

This bit powers down the force amplifier block. Note that the amplifier must be

powered up but inhibited (SW-INH or HW_INH), to meet leakage specifications. A 0

powers this block down (default).

LOAD

Updates to registers listed in the following LOAD function column do not occur until

the active LOAD pin is brought low (or in the case of LOAD 3, until BUSY goes high).

LOAD

LOAD Function

Default operation, CLEN and HW_INH function normally.

The CLEN pin is a LOAD input.

The HW_INH pin is a LOAD input.

The device senses the BUSY open-drain pin and doesn't update until that

goes high. No LOAD hardware pin. CLEN and HW_INH function normally.

6:0

Unused

Set to 0.

AD5560JSVUZ датащи(PDF) 48 Page - Analog Devices

AD5560JSVUZ датащи(HTML) 48 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

датащи скачать

ссылки URL