ELM327LP datasheet(4/94 Pages) ELM

4 / 94 page

ELM327L

Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

Pin Descriptions

4 of 94

MCLR (pin 1)

A momentary (>2µsec) logic low applied to this input

will reset the ELM327. If unused, this pin should be

connected to a logic high (VDD) level.

Vmeasure (pin 2)

This analog input is used to measure a 0 to 5V

signal that is applied to it. Care must be taken to

prevent the voltage from going outside of the supply

levels of the ELM327, or damage may occur. If it is

not used, this pin should be tied to either VDD or VSS.

J1850 Volts (pin 3)

This output can be used to control a voltage supply

for the J1850 Bus+ output. The pin normally outputs

a logic high level when a nominal 8V is required (for

J1850 VPW), and a low level for 5V (for J1850

PWM), but this can be changed with PP 12. The total

current into or from pin 3 must not exceed 2 mA.

J1850 Bus+ (pin 4)

This active high output is used to drive the

J1850 Bus+ Line to an active (low) level. The total

current into or from pin 4 must not exceed 2 mA.

Memory (pin 5)

This input controls the default state of the memory

option. If this pin is at a high level during power-up or

reset, the memory function will be enabled by

default. If it is at a low level, then the default will be

to have it disabled. Memory can always be enabled

or disabled with the AT M1 and AT M0 commands.

This input has Schmitt trigger waveshaping.

Filter Cap (pin 6)

The ELM327L requires that a 10µF filter capacitor be

connected between pin 6 and VSS. The capacitor

should be a low ESR (<5

Ω) ceramic or tantalum

type.

The ELM327 uses pin 6 for setting the initial baud

rate after power on. Since this option is not available

with the ELM327L, it defaults to an initial baud rate

of 38400 bps. If you require 9600 bps, you must set

PP 0C to 00.

LFmode (pin 7)

This input is used to select the default linefeed mode

to be used after a power-up or system reset. If it is at

a high level, then by default messages sent by the

ELM327 will be terminated with both a carriage

return and a linefeed character. If it is at a low level,

lines will be terminated by a carriage return only.

This behaviour can always be modified by issuing an

AT L1 or AT L0 command. This input has Schmitt

trigger waveshaping.

VSS (pin 8)

Circuit common must be connected to this pin.

XT1 (pin 9) and XT2 (pin 10)

A 4.000 MHz oscillator crystal is connected between

these two pins. Loading capacitors as required by

the crystal (typically 27pF each) will also need to be

connected between each of these pins and circuit

common (Vss).

Note that this device has not been configured for

operation with an external oscillator – it expects a

crystal to be connected to these pins. Use of an

external clock source is not recommended. Also,

note that this oscillator is turned off when in the Low

Power or ‘standby’ mode of operation.

VPW In (pin 11)

This is the active high input for the J1850 VPW data

signal. When at rest (bus recessive) this pin should

be at a low logic level. This input has Schmitt trigger

waveshaping, so no special amplification is required.

ISO In (pin 12)

This is the active low input for the ISO 9141 and

ISO 14230 data signal. It is derived from the K Line,

and should be at a high logic level when at rest (bus

recessive). No special amplification is required, as

this input has Schmitt trigger waveshaping.

PWM In (pin 13)

This is the active low input for the J1850 PWM data

signal. It should normally be at a high level when at

rest (ie. bus recessive). This input has Schmitt

trigger waveshaping, so no special amplification is

required.

J1850 Bus- (pin 14)

This active high output is used to drive the J1850

Bus- Line to an active (dominant) level for J1850

PWM applications.

ELM327L DSA

ELM327LP датащи(PDF) 4 Page - ELM Electronics

ELM327LP датащи(HTML) 4 Page - ELM Electronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

датащи скачать

ссылки URL