COM20022I datasheet(45/83 Pages) SMSC

45 / 83 page

10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Board RAM

Datasheet

SMSC COM20022I

Page 45

Rev. 08-18-03

DATASHEET

Table 6.11 - Setup 2 Register

BIT

BIT NAME

SYMBOL

DESCRIPTION

Read Bus Timing

Select

RBUSTMG

This bit is used to Disable/Enable the High Speed CPU Read

function for High Speed CPU bus support. RBUSTMG=0: Disable

(Default), RBUSTMG=1: Enable. That is, if BUSTMG (pin 26) = 1

and RBUSTMG = 1, High Speed CPU Read operations are

enabled. It does not influence write operation. High speed CPU

Read operation is only for non-multiplexed bus.

Reserved

This bit is undefined.

5,4

Clock Multiplier

CKUP1, 0

Higher frequency clocks are generated from the 20 MHz crystal

through the selection of these two bits as shown. This clock

multiplier is powered-down on default. After changing the CKUP1

and CKUP0 bits, the ARCNET core operation is stopped and the

internal PLL in the clock multiplier is awakened and it starts to

generate the 40 MHz. The lock out time of the internal PLL is 8

µSec

typically. After 1 mS it is necessary to write command data '18H' to

command register for re-starting the ARCNET core operation. EF

bit must be ‘1’ if the data rate is over 5Mbps.

CAUTION: Changing the CKUP1 and CKUP0 bits must be one

time or less after releasing a hardware reset.

CKUP1

CKUP0

Clock Frequency (Data Rate)

20 MHz (Up to 2.5Mbps) Default

40 MHz (Up to 5Mbps)

Reserved

80 MHz (Only 10Mbps)

Note:

After changing the CKUP1 or CKUP0 bits, it is necessary to

write a command data '18H' to the command register.

Because after changing the CKUP [1, 0] bits, the internal

operation is stopped temporarily. The writing of the

command is to start the operation.

These initializing steps are shown below.

Hardware reset (Power ON)

Change CKUP[1, 0] bit

Wait 1mSec (wait until stable oscillation)

Write command '18H' (start internal operation)

Start initializing routine (Execute existing software)

Enhanced Functions

This bit is used to enable the new enhanced functions in the

COM20022I. EF = 0: Disable (Default), EF = 1: Enable. If EF = 0,

the timing and function is the same as in the COM20020, Revision

B. See appendix “A”. EF bit must be ‘1’ if the data rate is over

5Mbps.

EF bit should be ‘1’ for new design customers.

EF bit should be ‘0’ for replacement customers.

No Synchronous

NOSYNC

This bit is used to enable the SYNC command during initialization.

NOSYNC= 0, Enable (Default) The line must be idle for the RAM

initialization sequence to be written. NOSYNC= 1, Disable:) The line

does not have to be idle for the RAM initialization sequence to be

written. See appendix “A”.

COM20022I датащи(PDF) 45 Page - SMSC Corporation

COM20022I датащи(HTML) 45 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

датащи скачать

ссылки URL