RN52 datasheet(19/26 Pages) MICROCHIP

19 / 26 page

 2015 Microchip Technology Inc.

DS70005120A-page 19

RN52

(RF) fields adopted by the Federal Communications

Commission (FCC). The bulletin offers guidelines and

suggestions for evaluating compliance.

If appropriate, compliance with exposure guidelines for

mobile and unlicensed devices can be accomplished

by the use of warning labels and by providing users

with information concerning minimum separation dis-

tances from transmitting structures and proper installa-

tion of antennas.

The following statement must be included as a CAU-

TION statement in manuals and OEM products to alert

users of FCC RF exposure compliance:

If the RN52 module is used in a portable application

(i.e., the antenna is less than 20 cm from persons

during operation), the integrator is responsible for per-

forming Specific Absorption Rate (SAR) testing in

accordance with FCC rules 2.1091.

4.1.3

HELPFUL WEB SITES

Federal Communications Commission (FCC):

http://www.fcc.gov

FCC Office of Engineering and Technology (OET)

Laboratory Division Knowledge Database (KDB):

http://apps.fcc.gov/oetcf/kdb/index.cfm

4.2

Canada

The RN52 module has been certified for use in Canada

under Industry Canada (IC) Radio Standards Specifica-

tion (RSS) RSS-210 and RSSGen. Modular approval

permits the installation of a module in a host device

without the need to recertify the device.

4.2.1

LABELING AND USER

INFORMATION REQUIREMENTS

Labeling Requirements for the Host Device (from Sec-

tion 3.2.1, RSS-Gen, Issue 3, December 2010): The

host device shall be properly labeled to identify the

module within the host device.

The Industry Canada certification label of a module

shall be clearly visible at all times when installed in the

host device, otherwise the host device must be labeled

to display the Industry Canada certification number of

the module, preceded by the words “Contains transmit-

ter module”, or the word “Contains”, or similar wording

expressing the same meaning, as follows:

User Manual Notice for License-Exempt Radio Appara-

tus (from Section 7.1.3 RSS-Gen, Issue 3, December

2010): User manuals for license-exempt radio appara-

tus shall contain the following or equivalent notice in a

conspicuous location

the

user

manual

alternatively on the device or both:

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue 3, December 2010): User manuals for transmit-

ters shall display the following notice in a conspicuous

location:

The above notice may be affixed to the device instead

of displayed in the user manual.

4.2.2

HELPFUL WEB SITES

Industry Canada: http://www.ic.gc.ca/

To satisfy FCC RF Exposure requirements for mobile

and base station transmission devices, a separation

distance of 20 cm or more should be maintained

between the antenna of this device and persons

during operation. To ensure compliance, operation at

closer than this distance is not recommended.

The antenna(s) used for this transmitter must not be

co-located or operating in conjunction with any other

antenna or transmitter.

Contains transmitter module IC: 6514A-RN52

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux con-

ditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le

fonctionnement.

Under Industry Canada regulations, this radio trans-

mitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the trans-

mitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotrop-

ically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d'Industrie Can-

ada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Can-

ada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il

faut choisir le type d'antenne et son gain de sorte

que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à

l'établissement d'une communication satisfaisante.

RN52 датащи(PDF) 19 Page - Microchip Technology

RN52 датащи(HTML) 19 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

датащи скачать

ссылки URL