AT90USB646 datasheet(94/456 Pages) ATMEL

94 / 456 page

7593L–AVR–09/12

AT90USB64/128

• Bits 7..0 – INT7 – INT0: External Interrupt Request 7 - 0 Enable

When an INT7 – INT0 bit is written to one and the I-bit in the Status Register (SREG) is set

(one), the corresponding external pin interrupt is enabled. The Interrupt Sense Control bits in the

External Interrupt Control Registers – EICRA and EICRB – defines whether the external inter-

rupt is activated on rising or falling edge or level sensed. Activity on any of these pins will trigger

an interrupt request even if the pin is enabled as an output. This provides a way of generating a

software interrupt.

12.0.4

EIFR – External Interrupt Flag Register

• Bits 7..0 – INTF7 - INTF0: External Interrupt Flags 7 - 0

When an edge or logic change on the INT7:0 pin triggers an interrupt request, INTF7:0 becomes

set (one). If the I-bit in SREG and the corresponding interrupt enable bit, INT7:0 in EIMSK, are

set (one), the MCU will jump to the interrupt vector. The flag is cleared when the interrupt routine

is executed. Alternatively, the flag can be cleared by writing a logical one to it. These flags are

always cleared when INT7:0 are configured as level interrupt. Note that when entering sleep

mode with the INT3:0 interrupts disabled, the input buffers on these pins will be disabled. This

may cause a logic change in internal signals which will set the INTF3:0 flags. See “Digital input

enable and sleep modes” on page 75 for more information.

12.0.5

PCICR – Pin Change Interrupt Control Register

• Bit 0 – PCIE0: Pin Change Interrupt Enable 0

When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an interrupt.

The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Interrupt

Vector. PCINT7..0 pins are enabled individually by the PCMSK0 Register.

12.0.6

PCIFR – Pin Change Interrupt Flag Register

• Bit 0 – PCIF0: Pin Change Interrupt Flag 0

When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0 becomes set

(one). If the I-bit in SREG and the PCIE0 bit in EIMSK are set (one), the MCU will jump to the

corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-

natively, the flag can be cleared by writing a logical one to it.

Bit

INTF7

INTF6

INTF5

INTF4

INTF3

INTF2

INTF1

IINTF0

EIFR

Read/write

R/W

Initial value

Bit

6543210

–

PCIE0

PCICR

Read/write

RRRRRRR/W

Initial value

0000000

Bit

6543210

–

–PCIF0

PCIFR

Read/write

RRRRRRR/W

Initial value

0000000

AT90USB646 датащи(PDF) 94 Page - ATMEL Corporation

AT90USB646 датащи(HTML) 94 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL