SC312XDP512F0MPVR datasheet(529/1348 Pages) FREESCALE

529 / 1348 page

Chapter 12 Serial Peripheral Interface (S12SPIV4)

MC9S12XDP512 Data Sheet, Rev. 2.21

Freescale Semiconductor

529

12.4.1

Master Mode

The SPI operates in master mode when the MSTR bit is set. Only a master SPI module can initiate

transmissions. A transmission begins by writing to the master SPI data register. If the shift register is

empty, the byte immediately transfers to the shift register. The byte begins shifting out on the MOSI pin

under the control of the serial clock.

•

Serial clock

The SPR2, SPR1, and SPR0 baud rate selection bits, in conjunction with the SPPR2, SPPR1, and

SPPR0 baud rate preselection bits in the SPI baud rate register, control the baud rate generator and

determine the speed of the transmission. The SCK pin is the SPI clock output. Through the SCK

pin, the baud rate generator of the master controls the shift register of the slave peripheral.

•

MOSI, MISO pin

In master mode, the function of the serial data output pin (MOSI) and the serial data input pin

(MISO) is determined by the SPC0 and BIDIROE control bits.

•

SS pin

If MODFEN and SSOE are set, the SS pin is conﬁgured as slave select output. The SS output

becomes low during each transmission and is high when the SPI is in idle state.

If MODFEN is set and SSOE is cleared, the SS pin is conﬁgured as input for detecting mode fault

error. If the SS input becomes low this indicates a mode fault error where another master tries to

drive the MOSI and SCK lines. In this case, the SPI immediately switches to slave mode, by

clearing the MSTR bit and also disables the slave output buffer MISO (or SISO in bidirectional

mode). So the result is that all outputs are disabled and SCK, MOSI, and MISO are inputs. If a

transmission is in progress when the mode fault occurs, the transmission is aborted and the SPI is

forced into idle state.

This mode fault error also sets the mode fault (MODF) ﬂag in the SPI status register (SPISR). If

the SPI interrupt enable bit (SPIE) is set when the MODF ﬂag becomes set, then an SPI interrupt

sequence is also requested.

When a write to the SPI data register in the master occurs, there is a half SCK-cycle delay. After

the delay, SCK is started within the master. The rest of the transfer operation differs slightly,

depending on the clock format speciﬁed by the SPI clock phase bit, CPHA, in SPI control register 1

(see Section 12.4.3, “Transmission Formats”).

NOTE

A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0, or

BIDIROE with SPC0 set, SPPR2-SPPR0 and SPR2-SPR0 in master mode

will abort a transmission in progress and force the SPI into idle state. The

remote slave cannot detect this, therefore the master must ensure that the

remote slave is returned to idle state.

SC312XDP512F0MPVR датащи(PDF) 529 Page - Freescale Semiconductor, Inc

SC312XDP512F0MPVR датащи(HTML) 529 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL