TS8GDOM40V datasheet(47/52 Pages) TRANSCEND

47 / 52 page

rra

d 4

0---P

Piiin

n IIID

E F

Fllla

h M

ullle

B ~

~ 8

Transcend Information Inc.

Ver 1.7

Device Terminating an Ultra DMA Data-Out Burst

The device terminates an Ultra DMA Data-Out burst by following the steps lettered below. The timing

diagram for the operation is shown in below: Ultra DMA Data-Out Burst Device Termination Timing. The

timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are

described in Page 13: Ultra DMA Data Burst Timing Descriptions.

The following steps shall occur in the order they are listed unless otherwise specifically allowed:

(a) The device shall not initiate Ultra DMA data burst termination until at least one data word of an Ultra

DMA data burst has been transferred.

(b) The device shall initiate Ultra DMA data burst termination by negating -DDMARDY.

(d) While operating in Ultra DMA modes 2, 1, or 0 the device shall be prepared to receive zero, one or two

additional data words after negating -HDMARDY. While operating in Ultra DMA modes 4 or 3 the

device shall be prepared to receive zero, one, two or three additional data words. The additional

data words are a result of cable round trip delay and tRFS timing for the device.

(e) The device shall negate DMARQ no sooner than tRP after negating -DDMARDY. The device shall not

assert DMARQ again until after the Ultra DMA data burst is terminated.

(f) The host shall assert STOP within tLI after the device has negated DMARQ. The host shall not negate

STOP again until after the Ultra DMA data burst is terminated.

(g) If HSTROBE is negated, the host shall assert HSTROBE within tLI after the device has negated

DMARQ. No data shall be transferred during this assertion. The device shall ignore this transition of

HSTROBE. HSTROBE shall remain asserted until the Ultra DMA data burst is terminated.

(h) The host shall place the result of its CRC calculation on D[15:00] (see ATA specification Ultra DMA

CRC Calculation).

(i) The host shall negate -DMACK no sooner than tMLI after the host has asserted HSTROBE and STOP

and the device has negated DMARQ and -DDMARDY, and no sooner than tDVS after placing the result

of its CRC calculation on D[15:00].

(j) The device shall latch the host’s CRC data from D[15:00] on the negating edge of -DMACK.

(k) The device shall compare the CRC data received from the host with the results of its own CRC

calculation. If a miscompare error occurs during one or more Ultra DMA data bursts for any one

command, the device shall report the first error that occurred (see ATA specification Ultra DMA CRC

Calculation).

(l) While operating in True IDE mode, the device shall release DSTROBE within tIORDYZ after the host

negates -DMACK.

(m) The host shall not negate STOP nor assert –HDMARDY until at least tACK after negating -DMACK.

(n) In True IDE mode, the host shall not assert -IOWR, -CS0, -CS1, nor A[02:00] until at least tACK after

negating DMACK.

TS8GDOM40V датащи(PDF) 47 Page - Transcend Information. Inc.

TS8GDOM40V датащи(HTML) 47 Page - Transcend Information. Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

датащи скачать

ссылки URL