LPC2364 datasheet(13/59 Pages) NXP

13 / 59 page

LPC2364_65_66_67_68_6

Product data sheet

Rev. 06 — 1 February 2010

13 of 59

NXP Semiconductors

LPC2364/65/66/67/68

Single-chip 16-bit/32-bit microcontrollers

P2[1]/PWM1[2]/

RXD1/

PIPESTAT0

74[1]

B10[1]

I/O

P2[1] — General purpose digital input/output pin.

PWM1[2] — Pulse Width Modulator 1, channel 2 output.

RXD1 — Receiver input for UART1.

PIPESTAT0 — Pipeline Status, bit 0.

P2[2]/PWM1[3]/

CTS1/

PIPESTAT1

73[1]

D8[1]

I/O

P2[2] — General purpose digital input/output pin.

PWM1[3] — Pulse Width Modulator 1, channel 3 output.

CTS1 — Clear to Send input for UART1.

PIPESTAT1 — Pipeline Status, bit 1.

P2[3]/PWM1[4]/

DCD1/

PIPESTAT2

70[1]

E7[1]

I/O

P2[3] — General purpose digital input/output pin.

PWM1[4] — Pulse Width Modulator 1, channel 4 output.

DCD1 — Data Carrier Detect input for UART1.

PIPESTAT2 — Pipeline Status, bit 2.

P2[4]/PWM1[5]/

DSR1/

TRACESYNC

69[1]

D9[1]

I/O

P2[4] — General purpose digital input/output pin.

PWM1[5] — Pulse Width Modulator 1, channel 5 output.

DSR1 — Data Set Ready input for UART1.

TRACESYNC — Trace Synchronization.

P2[5]/PWM1[6]/

DTR1/

TRACEPKT0

68[1]

D10[1]

I/O

P2[5] — General purpose digital input/output pin.

PWM1[6] — Pulse Width Modulator 1, channel 6 output.

DTR1 — Data Terminal Ready output for UART1.

TRACEPKT0 — Trace Packet, bit 0.

P2[6]/PCAP1[0]/

RI1/

TRACEPKT1

67[1]

E8[1]

I/O

P2[6] — General purpose digital input/output pin.

PCAP1[0] — Capture input for PWM1, channel 0.

RI1 — Ring Indicator input for UART1.

TRACEPKT1 — Trace Packet, bit 1.

P2[7]/RD2/

RTS1/

TRACEPKT2

66[1]

E9[1]

I/O

P2[7] — General purpose digital input/output pin.

RD2 — CAN2 receiver input. (LPC2364/66/68 only)

RTS1 — Request to Send output for UART1.

TRACEPKT2 — Trace Packet, bit 2.

P2[8]/TD2/

TXD2/

TRACEPKT3

65[1]

E10[1]

I/O

P2[8] — General purpose digital input/output pin.

TD2 — CAN2 transmitter output. (LPC2364/66/68 only)

TXD2 — Transmitter output for UART2.

TRACEPKT3 — Trace Packet, bit 3.

P2[9]/

USB_CONNECT/

RXD2/EXTIN0

64[1]

F7[1]

I/O

P2[9] — General purpose digital input/output pin.

USB_CONNECT — Signal used to switch an external 1.5 k

Ω resistor under

software control. Used with the SoftConnect USB feature. (LPC2364/66/68

only)

RXD2 — Receiver input for UART2.

EXTIN0 — External Trigger Input.

P2[10]/EINT0

53[6]

J10[6]

I/O

P2[10] — General purpose digital input/output pin.

Note: LOW on this pin while RESET is LOW forces on-chip bootloader to

take over control of the part after a reset.

EINT0 — External interrupt 0 input.

Table 4.

Pin description …continued

Symbol

Ball

Type

Description

LPC2364 датащи(PDF) 13 Page - NXP Semiconductors

LPC2364 датащи(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

датащи скачать

ссылки URL