AD9393SLASHPCBZ datasheet(31/40 Pages) AD

31 / 40 page

AD9393

Rev. 0 | Page 31 of 40

2-WIRE SERIAL CONTROL PORT

A 2-wire serial interface control interface is provided in the

AD9393.

The 2-wire serial interface is comprised of a clock (SCL) and a

bidirectional data (SDA) ball. The HDMI flat panel interface

acts as a slave for receiving and transmitting data over the serial

interface. When the serial interface is not active, the logic levels

on SCL and SDA are pulled high by external pull-up resistors.

Data received or transmitted on the SDA line must be stable for

the duration of the positive-going SCL pulse. Change data on

SDA only when SCL is low. If SDA changes state while SCL is

high, the serial interface interprets that action as a start or stop

sequence.

There are six components to serial bus operation:

•

Start signal

•

Slave address byte

•

Base register address byte

•

Data byte to read or write

•

Stop signal

•

Acknowledge (ACK)

When the serial interface is inactive (SCL and SDA are high),

communications are initiated by sending a start signal. The start

signal is a high-to-low transition on SDA while SCL is high.

This signal alerts all slave devices that a data transfer sequence

is coming.

The first eight bits of data transferred after a start signal

comprise an 7-bit slave address (the first 7 bits) and a single

R/W bit (the eight bit). The R/W bit indicates the direction of

the data transfer, read from (1) or write to (0) the slave device. If

the transmitted slave address matches the address of the device,

the AD9393 acknowledges by bringing SDA low on the ninth

SCL pulse. If the addresses do not match, the AD9393 does not

acknowledge.

Table 28. Serial Port Addresses

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

A6 (MSB)

R/W

DATA TRANSFER VIA SERIAL INTERFACE

For each byte of data read or written, the MSB is the first bit of

the sequence.

If the AD9393 does not acknowledge the master device during a

write sequence, the SDA remains high so the master can gener-

ate a stop signal. If the master device does not acknowledge the

AD9393 during a read sequence, the AD9393 interprets this as

the end of data. The SDA remains high, so the master can

generate a stop signal.

To write data to specific control registers of the AD9393, the

8-bit address of the control register of interest must be written

after the slave address has been established. This control register

address is the base address for subsequent write operations. The

base address autoincrements by 1 for each byte of data written

after the data byte intended for the base address. If more bytes

are transferred than there are available addresses, the address

does not increment and remains at its maximum value. Any

base address higher than the maximum value does not produce

an acknowledge signal.

Data are read from the control registers of the AD9393 in a

similar manner. Reading requires two data transfer operations:

•

The base address must be written with the R/W bit of the

slave address byte low to set up a sequential read operation.

•

Reading (the R/W bit of the slave address byte high)

begins at the previously established base address. The

address of the read register autoincrements after each

byte is transferred.

To terminate a read/write sequence to the AD9393, a stop signal

must be sent. A stop signal comprises a low-to-high transition

of SDA while SCL is high.

A repeated start signal occurs when the master device driving

the serial interface generates a start signal without first genera-

ting a stop signal to terminate the current communication.

This is used to change the mode of communication (read,

write) between the slave and master without releasing the

serial interface lines.

SDA

SCL

tBUFF

tSTAH

tDHO

tDSU

tDAL

tDAH

tSTASU

tSTOSU

Figure 7. Serial Port Read/Write Timing

AD9393/PCBZ датащи(PDF) 31 Page - Analog Devices

AD9393/PCBZ датащи(HTML) 31 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL