ATmega328P datasheet(242/448 Pages) ATMEL

242 / 448 page

242

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

• Bit 7 – TWINT: TWI Interrupt Flag

This bit is set by hardware when the TWI has finished its current job and expects application

software response. If the I-bit in SREG and TWIE in TWCR are set, the MCU will jump to the

TWI Interrupt Vector. While the TWINT Flag is set, the SCL low period is stretched. The TWINT

Flag must be cleared by software by writing a logic one to it. Note that this flag is not automati-

cally cleared by hardware when executing the interrupt routine. Also note that clearing this flag

starts the operation of the TWI, so all accesses to the TWI Address Register (TWAR), TWI Sta-

tus Register (TWSR), and TWI Data Register (TWDR) must be complete before clearing this

flag.

• Bit 6 – TWEA: TWI Enable Acknowledge Bit

The TWEA bit controls the generation of the acknowledge pulse. If the TWEA bit is written to

one, the ACK pulse is generated on the TWI bus if the following conditions are met:

The device’s own slave address has been received.

A general call has been received, while the TWGCE bit in the TWAR is set.

A data byte has been received in Master Receiver or Slave Receiver mode.

By writing the TWEA bit to zero, the device can be virtually disconnected from the 2-wire Serial

Bus temporarily. Address recognition can then be resumed by writing the TWEA bit to one

again.

• Bit 5 – TWSTA: TWI START Condition Bit

The application writes the TWSTA bit to one when it desires to become a Master on the 2-wire

Serial Bus. The TWI hardware checks if the bus is available, and generates a START condition

on the bus if it is free. However, if the bus is not free, the TWI waits until a STOP condition is

detected, and then generates a new START condition to claim the bus Master status. TWSTA

must be cleared by software when the START condition has been transmitted.

• Bit 4 – TWSTO: TWI STOP Condition Bit

Writing the TWSTO bit to one in Master mode will generate a STOP condition on the 2-wire

Serial Bus. When the STOP condition is executed on the bus, the TWSTO bit is cleared auto-

matically. In Slave mode, setting the TWSTO bit can be used to recover from an error condition.

This will not generate a STOP condition, but the TWI returns to a well-defined unaddressed

Slave mode and releases the SCL and SDA lines to a high impedance state.

• Bit 3 – TWWC: TWI Write Collision Flag

The TWWC bit is set when attempting to write to the TWI Data Register – TWDR when TWINT is

low. This flag is cleared by writing the TWDR Register when TWINT is high.

• Bit 2 – TWEN: TWI Enable Bit

The TWEN bit enables TWI operation and activates the TWI interface. When TWEN is written to

one, the TWI takes control over the I/O pins connected to the SCL and SDA pins, enabling the

slew-rate limiters and spike filters. If this bit is written to zero, the TWI is switched off and all TWI

transmissions are terminated, regardless of any ongoing operation.

• Bit 1 – Res: Reserved Bit

This bit is a reserved bit and will always read as zero.

ATmega328P датащи(PDF) 242 Page - ATMEL Corporation

ATmega328P датащи(HTML) 242 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL