ATmega328P datasheet(206/448 Pages) ATMEL

206 / 448 page

206

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

Figure 20-1. UCPHAn and UCPOLn data transfer timing diagrams.

20.5

Frame Formats

A serial frame for the MSPIM is defined to be one character of 8 data bits. The USART in MSPIM

mode has two valid frame formats:

• 8-bit data with MSB first

• 8-bit data with LSB first

A frame starts with the least or most significant data bit. Then the next data bits, up to a total of

eight, are succeeding, ending with the most or least significant bit accordingly. When a complete

frame is transmitted, a new frame can directly follow it, or the communication line can be set to

an idle (high) state.

The UDORDn bit in UCSRnC sets the frame format used by the USART in MSPIM mode. The

Receiver and Transmitter use the same setting. Note that changing the setting of any of these

bits will corrupt all ongoing communication for both the Receiver and Transmitter.

16-bit data transfer can be achieved by writing two data bytes to UDRn. A UART transmit com-

plete interrupt will then signal that the 16-bit value has been shifted out.

20.5.1

USART MSPIM Initialization

The USART in MSPIM mode has to be initialized before any communication can take place. The

initialization process normally consists of setting the baud rate, setting master mode of operation

(by setting DDR_XCKn to one), setting frame format and enabling the Transmitter and the

Receiver. Only the transmitter can operate independently. For interrupt driven USART opera-

tion, the Global Interrupt Flag should be cleared (and thus interrupts globally disabled) when

doing the initialization.

Note:

To ensure immediate initialization of the XCKn output the baud-rate register (UBRRn) must be

zero at the time the transmitter is enabled. Contrary to the normal mode USART operation the

UBRRn must then be written to the desired value after the transmitter is enabled, but before the

first transmission is started. Setting UBRRn to zero before enabling the transmitter is not neces-

sary if the initialization is done immediately after a reset since UBRRn is reset to zero.

Before doing a re-initialization with changed baud rate, data mode, or frame format, be sure that

there is no ongoing transmissions during the period the registers are changed. The TXCn Flag

can be used to check that the Transmitter has completed all transfers, and the RXCn Flag can

XCK

Data setup (TXD)

Data sample (RXD)

XCK

Data setup (TXD)

Data sample (RXD)

XCK

Data setup (TXD)

Data sample (RXD)

XCK

Data setup (TXD)

Data sample (RXD)

UCPOL=0

UCPOL=1

ATmega328P датащи(PDF) 206 Page - ATMEL Corporation

ATmega328P датащи(HTML) 206 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL