ATmega169P datasheet(157/393 Pages) ATMEL

157 / 393 page

157

8018N–AVR–08/09

ATmega169P

32 kHz crystal. Writing to EXCLK should be done before asynchronous operation is selected.

Note that the crystal Oscillator will only run when this bit is zero.

• Bit 3 – AS2: Asynchronous Timer/Counter2

When AS2 is written to zero, Timer/Counter2 is clocked from the I/O clock, clk

I/O. When AS2 is

written to one, Timer/Counter2 is clocked from a crystal Oscillator connected to the Timer Oscil-

lator 1 (TOSC1) pin. When the value of AS2 is changed, the contents of TCNT2, OCR2A, and

TCCR2A might be corrupted.

• Bit 2 – TCN2UB: Timer/Counter2 Update Busy

When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes set.

When TCNT2 has been updated from the temporary storage register, this bit is cleared by hard-

ware. A logical zero in this bit indicates that TCNT2 is ready to be updated with a new value.

• Bit 1 – OCR2UB: Output Compare Register2 Update Busy

When Timer/Counter2 operates asynchronously and OCR2A is written, this bit becomes set.

When OCR2A has been updated from the temporary storage register, this bit is cleared by hard-

ware. A logical zero in this bit indicates that OCR2A is ready to be updated with a new value.

• Bit 0 – TCR2UB: Timer/Counter Control Register2 Update Busy

When Timer/Counter2 operates asynchronously and TCCR2A is written, this bit becomes set.

When TCCR2A has been updated from the temporary storage register, this bit is cleared by

hardware. A logical zero in this bit indicates that TCCR2A is ready to be updated with a new

value.

If a write is performed to any of the three Timer/Counter2 Registers while its update busy flag is

set, the updated value might get corrupted and cause an unintentional interrupt to occur.

The mechanisms for reading TCNT2, OCR2A, and TCCR2A are different. When reading

TCNT2, the actual timer value is read. When reading OCR2A or TCCR2A, the value in the tem-

porary storage register is read.

17.10.7

GTCCR – General Timer/Counter Control Register

• Bit 1 – PSR2: Prescaler Reset Timer/Counter2

When this bit is one, the Timer/Counter2 prescaler will be reset. This bit is normally cleared

immediately by hardware. If the bit is written when Timer/Counter2 is operating in asynchronous

mode, the bit will remain one until the prescaler has been reset. The bit will not be cleared by

hardware if the TSM bit is set. Refer to the description of the ”Bit 7 – TSM: Timer/Counter Syn-

chronization Mode” on page 137 for a description of the Timer/Counter Synchronization mode.

Bit

0x23 (0x43)

TSM

–

PSR2

PSR10

GTCCR

Read/Write

R/W

Initial Value

ATmega169P датащи(PDF) 157 Page - ATMEL Corporation

ATmega169P датащи(HTML) 157 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL