ATmega165 datasheet(126/336 Pages) ATMEL

126 / 336 page

126

ATmega165/V

2573G–AVR–07/09

compare match. The counter will then have to count to its maximum value (0xFF) and

wrap around starting at 0x00 before the compare match can occur.

For generating a waveform output in CTC mode, the OC2A output can be set to toggle

its logical level on each compare match by setting the Compare Output mode bits to tog-

gle mode (COM2A1:0 = 1). The OC2A value will not be visible on the port pin unless the

data direction for the pin is set to output. The waveform generated will have a maximum

frequency of f

OC2A = fclk_I/O/2 when OCR2A is set to zero (0x00). The waveform fre-

quency is defined by the following equation:

The N variable represents the prescale factor (1, 8, 32, 64, 128, 256, or 1024).

As for the Normal mode of operation, the TOV2 Flag is set in the same timer clock cycle

that the counter counts from MAX to 0x00.

Fast PWM Mode

The fast Pulse Width Modulation or fast PWM mode (WGM21:0 = 3) provides a high fre-

quency PWM waveform generation option. The fast PWM differs from the other PWM

option by its single-slope operation. The counter counts from BOTTOM to MAX then

restarts from BOTTOM. In non-inverting Compare Output mode, the Output Compare

(OC2A) is cleared on the compare match between TCNT2 and OCR2A, and set at BOT-

TOM. In inverting Compare Output mode, the output is set on compare match and

cleared at BOTTOM. Due to the single-slope operation, the operating frequency of the

fast PWM mode can be twice as high as the phase correct PWM mode that uses dual-

slope operation. This high frequency makes the fast PWM mode well suited for power

regulation, rectification, and DAC applications. High frequency allows physically small

sized external components (coils, capacitors), and therefore reduces total system cost.

In fast PWM mode, the counter is incremented until the counter value matches the MAX

value. The counter is then cleared at the following timer clock cycle. The timing diagram

for the fast PWM mode is shown in Figure 58. The TCNT2 value is in the timing diagram

shown as a histogram for illustrating the single-slope operation. The diagram includes

non-inverted and inverted PWM outputs. The small horizontal line marks on the TCNT2

slopes represent compare matches between OCR2A and TCNT2.

Figure 58. Fast PWM Mode, Timing Diagram

fOCnx

clk_I/O

OCRnx

()

⋅⋅

--------------------------------------------------

TCNTn

OCRnx Update and

TOVn Interrupt Flag Set

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

OCRnx Interrupt Flag Set

ATmega165 датащи(PDF) 126 Page - ATMEL Corporation

ATmega165 датащи(HTML) 126 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL